Subject: Ayers Rock Helio Courier
From: Rotary Engine
Date: 8/30/2009, 5:22 AM
To: AAA Put this in the To box


Thanks Paul,

The photos bring back memories. My first posting as a
Ranger was to Ayers Rock, in the
early '80's. Spent two and a half years clambering over it,
the Olgas, Kings Canyon
and anywhere else that looked interesting, before moving
back North to the saltwater country.

I made mention earlier of the Helio Courier. Do you know
why they stopped making them?
I watched the 1954 promo on utube and was impressed with
the STOL performance. Seems
the company that was making them in the '80's went bust.
I'm surprised no-one has
used the wing design (auto slats and retactable flaps) in
more of today's STOL

aircraft. For an aircraft that could land on two/fifths of
bugger-all and also
crank out some pretty impressive knots seems a pity they're
not still produced.


Cheers,

Stewart

Nice airplane. I think when Air America got out of South
East asia
the main market dried up :) Too expensive.


Paul Lamar



From: Rotary Engine [mailto:rotaryeng@earthlink.net]
Sent: Sun 30/08/2009 12:31 PM
To: AAA Put this in the To box
Subject: advice/ideas/enlightenment





Im writing to you from Australia and am after some
advice/ideas/enlightenment.
I am not yet a pilot; however I hope to soon have a
licence. I
also hope to, in the nearer rather than further future,
build a
kit aircraft and I wish to power it with a rotary engine.
To
that end, I have been researching as much as I can on the
internet.

I am a subscriber to your newsletter, I have Traceys manual
on
rotary conversion and have gathered heaps of great info on
rotary engines.

My dilemma is:
*   Everything anyone writes about seems to
be in the
200Hp-300+Hp, and usually based around the 13B, or larger-
(3,4,6 rotors. Good Grief! Now maybe if I could just find
and
afford a Helio Courier that needed an engine and a good
home)

*    The aircraft I want is a STOL Hornet built
by
    Australian Aircraft Kits
www.aircraftkits.com.au and is rated
    for 120Hp. It is a 2 + cargo, or a 2 + 2. I
have been in
    contact with the company and they seemed
happy to accept a
    rotary in the 120Hp-140Hp range and said they
would need to
    provide wing extensions to counter the weight
of the rotary.

I have purchased a stock 12A (which I understand falls into
the
120-140Hp bracket) from a wrecking yard that seems to be in
good
condition. If it measures up, then Im happy to put a master
kit
through it and build it up as a power plant.

I know I will loose out on the power to weight ratio that
rotaries are famous for, but so be it. If I could afford a
set
of Racing Beat alloy plates Id be ahead of the game.

In your opinion,
*    is it worth my while to continue down this
road and
build up this 12A, given the (relatively) low Hp required?
Or
are there better options you are aware of? Rotamax????
*    If I do continue, am I better off looking to
EFI of
carburetted?
*    What PSRU would you recommend?

I am not an engineer, electrician, or have any sort of
trade
background. I am pretty handy with most forms of metal
fabrication and welding though and can usually get around a
set
of plans or diagrams without too much drama.

Any help you can provide will be greatly appreciated.

Yours in anticipation,

Stewart Woerle.


Stewart Woerle
Nathan River Ranger Station
Limmen National Park
PMB 133
Katherine NT 0852

When aircraft builders are thinking of limiting the HP what
they are assuming
is you are going to use an aircraft engine. Well what they
are really thinking
about is increased weight with more HP always results in
more weight in a air
cooled aircraft engine. More HP will not intrinsically hurt
an aircraft
in any way if you don't use it. True it can be hard to
control at sea level
during take off due to torque effects but you don't have to
open the throttle
all they way if you don't want to.  Where more HP pays
off is at high altitude
where the drag is down and the additionally HP allows you
to cruise faster.
I have flown all over your fine, beautiful and large
country in
a C172 and what you really need is a faster airplane :)
Another advantage is
you cannot have too much HP in a STOL. To get off in a
short field what
you need is rapid acceleration to flying speed. Read a
large diameter prop
with lots of HP to turn it. In that case what ever engine
you choose,
12A or 13B, use a p-port as it is a cheap additional 50 HP
with no increase
in weight or fuel burn if you don't use it a cruise. In
fact the weight of
the p-port intake manifold is less than the weight of a
side port manifold.

Now that we have that discussed lets talk about engine
weight. The 12A is no lighter
than a 13B mostly due to the cast iron water pump. One
advantage it has is cost.
Here in the states they are in many cases free.

Now I am a little worried about your choice of aircraft
company as adding
extensions to the wings is not a smart thing to do. You
risk wing failure
in turbulences and in normal maneuvers. The current wing is
structurally designed
(or it should be) for  the amount of surface area it
has and the gross weight of
the airplane.

Now a low cost for the kit may be your main concern but the
time it takes
to build an aircraft is not necessarily related to the
size. I would
pick a low cost fast build STOL kit aircraft that was
designed for the weight
of the 13B or 12A engine. A Zenair 800 is a low cost STOL
aircraft
that will accommodate the weight of a 13B. You might find
an Australian
version that will do the same thing.

Rotamax is out of business.
A  500 CFM 2 barrel Holley carb with leaning kit is
the lowest cost way to go.
Tracy's PSRU works fine.

Paul Lamar

-

Thanks very much Paul,

  I'll take that onboard and continue with the
research. Had
already considered the 801, so may need to revisit that
idea.

On another matter, could you please unsubscribe me from
this
address and rather send to; stewartjohann@hotmail.com

thanks again,

Stewart

I think the 801 with a 250 HP rotary would make a great out
back airplane.
You never know when you might need to land in a small
spot.
The lower the stall speed the less energy in the crash.

The formula for the crash energy is M X V squared. That is
why the
FAA in the states mandate a 61 kt stall speed for single
engine
aircraft. 50 times 50 is 2500...... 60 times 60 is 3600. A
50% more violent
crash.

Here are some pictures I took from the C172.

Paul Lamar

--

Stewart, A couple of STOL aircraft to look at are the Bearhawk and the
Bearhawk Patrol.  They can be had from plans built up to quick build
kits.  They would work well with a rotary.

Joel





-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.