Snip.....
----------------------------------------------
I changed to 804 and it does pretty much the same things.
I went out and spent $400 bucks on a new MegaByte mother
board, processor
and memory. Guess what. Unbuntu refused to load.
In frustration a grabbed and old Fedora 5 and stuck it in
the DVD drive.
Guess what? It loaded right off the bat with no problems.
Fedora install program is ten times better than Ubuntu
keeping
you well informed on what it is doing, why it is doing what
it is doing
and how long it is going to take. Unbuntu sometimes gives
you a blinking
cursor
and other times nothing and sometimes the light blinks on
the DVD drive.
Fedora 5 also loaded on the board above with no problems.
BTW there is no need for half the stuff on the install
distro.
Who is going to use open office on their mill computer??
If they removed half that useless stuff it would take a lot
less time
to load and install.
--------------------------------------------------
I took that GigaByte mother board back and got my money
back.
Worst mother board and BIOS I ever had the displeasure to
use.
BTW the hot tip is to install Fedora first and let
it scope out the hard drive. It does a much better job.
Then install Ubuntu if you must :)
Paul Lamar
Paul,
Sorry to hear that you are having so much trouble loading
Ubuntu.
I went to the Gmane linux emc users forum and typed in
"grub error 18" and
got a lot of hits.
See here:
http://search.gmane.org/search.php?group=gmane.linux.distributions.emc.user&
query=grub+error+18
I also found a debug trick that might help you, here is a
partial quote from
one of the above web site hits:
"...when the system is first booting up, right after the
manufacturer's splash screen (if any), it says :
GRUB loading, please wait...
Hit ESC at that time, and you get a menu. Generally
the last
item on the menu is the Memtest86 program, just hit the
down
arrow key to highlight that entry and h it return.
This
diagnostic will run forever if it finds no errors,
otherwise it
will list what it has found wrong, at a fairly technical
level.
But, what you are looking for is the presence or absence
of
error reports. It may also be that your BIOS settings
have
gotten corrupted, or that someone overclocked the computer
for
gaming, and the settings are not correct for proper
operation.
Most BIOS setup screens have some option to return all
settings
to default, you might try that if you haven't made any
special
settings for specific hardware compatibility."
Good luck,
Tom
Yes I did that Tom. That works for testing the memory.
One of the neat things about it is it times it self.
When I first used the SOYO board it would run for 12.5
minutes
and crash. Turned out there was a linear voltage regulator
on
the board that was overheating and shutting down.
I dug up an old 115 volt 13 watt AC fan I had lying around
and applied that sledge hammer. Problem went away. I am
looking
for a heat sink to glue to the top of the linear regulator
chips.
---------------------------------------------------------
I ordered ten of these heat sinks so if anybody needs some
let
me know. I'll sell up to six for $5 each plus $5 flat rate
mail cash
only. They are 15 by 15 mm so they will glue down on top.
Comes
with the proper glue.
All the new mother boards use the 12 Volt supply for the
processors
with these linear regulators dropping it down to 3
volts or so
for the processor. In fact there are separate lines from
the new power
supplies that are dedicated to the processor power alone.
If you don't
connect them up the processor won't boot. Been there done
that.
See the JPG.
Consequently these regulators run hotter than
hades when you are running the new 3 Giga Hertz high speed,
high power
processors. These board use over 500 watts of power which
is
about 2/3rds of a HP.
Paul Lamar
Paul,
The board really needs to be in a case with positive airflow.
You've solved part of the issue with heat sinks.... but you'll have some
additional "problems" crop up that will be solved with a good case and airflow.
To give you an idea, one of the parts on that board works fine up to 70C
Ambient.
Theta JA (Junction to Ambient) is about 40 C/W.
With 1 m/s (meter/second) airflow it will be around 35 C/W
With 2 m/s airflow.... drops around 32 C/W.
While there may not seem like that much difference, the Ambient temp is
already at 70C from the neighboring part. Turn it on, 2 W of power, and
you've increased that part anther 80C. Yes, it will blister a finger.
Put everything in a box, get air flowing over it... Ambient will drop to
around 40C, so the part won't be too hot. Airflow will also help carry
off some heat, giving maximum reliability.
For the machine shop area... Automotive Airfilters. I like NAPA gold,
and will glance at boxes till I see one about the right size. If you
have a grinding operations, those particles get small enough to get
pass automotive air filters. A post HEPA filter will work. Good news
is the dishwasher with a little cascade, followed by a low 150F oven
bake overnight will usually bring the board back to life.
Tom Walter
The K7 SOYO 750 Giga Hertz board is going in a 19" rack with that 13 watt 115 Volt
wind tunnel blower :)
My wife used that K7 SOYO board in a PC case for about a year and it would
do the same thing. I did not bother to trouble shoot it then and
merely replaced it with a Mac notebook as she was fed up with the Windows
virus thing.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.