Subject: Zenith 801 FACTS !!!] Ben Hass replies
From: Rotary Engine
Date: 9/11/2009, 11:57 AM
To: AAA Put this in the To box


 On the "801"

 This is an accident waiting to happen. The motor mount is
 incorrectly
 designed with un triangulated bays and bent tubes in
 tension and compression.
 The firewall forward weight is at least 450 pounds aluminum
 block or no
 aluminum block. No mention is made of beefing up the
 fuselage to take the
 vastly increased bending loads during landing and high G
 turns not to
 mention the increased bending loads on the wing spars.
 Zenairs are not
 over  designed to begin with having very thin skins.

 "The fuel burn is better then expected though and I am
 presently
 confirming the JPI 450 for accuracy. Cruise @ 11,000 msl is
 producing
 5.9 0 -6.3  gallons an hour."

 The numbers quoted above shows a lack of understanding
 about engine
 engineering in general. The fuel burn quoted at 6 gallons
 an hour
 or 37 pounds an hour means the engine is only generating 83
 HP giving
 it the benefit of a BSFC number of .45. In the unlikely
 event the BSFC
 is as low as .40 the HP then would be 93 HP at the absolute
 maximum.
 Now you have a 450 pound firewall forward weight putting
 out 93 HP at cruise.

 Something is seriously wrong.

  "The numbers I am shooting for are one pound of
 engine weight for each
 horsepower and a small total engine profile that will fit
 in most airframes."

 What he is saying here is he things he is going to get 350
 to 400 HP
 with a 1.43:1 PSRU ratio. With a 2600 RPM prop that is 3700
 engine
 RPM. No way is that going to happen.

 This person is totally clueless.

 I am really worried here. Probably one of the most
 dangerous  airplanes
 I have seen in a very long time.

 Paul Lamar




-------------------------------------------------------------------------------------------------------------------------------------------

 I don't know who this "person" is or what his
 qualifications, but..

 I am compelled to answer his hatchet job on every topic.

 My project is a one of a kind. I had no group, forum or any
 other source
 to go to during the design, and test flying of my
 experimental aircraft,
 so all the calculations, fabrications and installations
 are a one off
 and done to the best of my ability using past life
 experiences from
 fabricating stuff on race boats, cars and god only knows
 whatever I
 have modified in earlier years.

 I built my plane, 3000 + hours of MY time. I didn't but a
 half built
 one, or a completed one to use a test bed for my
 powerplant. I have
 been flying for almost 30 years and owned several other
 planes.

    My experimental plane has been flying for 5
 years and 300 hours.
 Been flown in air from 97f   to -37f. Has
 over 500 landing, been flown
 from JAC, 6430 msl to 18,000 feet, full throttle, !! over a
 couple of
 dozen times to test it for strength. Been flown in all
 other power
 settings to comfirm and quantify data. Tested to +3.5g's to
 - 2.5 g's.
 Flown to OSH and back... not trucked there as others seem
 to do
 to display their creations.

 My responses..

 1- When is this " accident" going to happen ??

 2- The mount is designed by me using triangulation, just go
 to my
 web site and look at the pics.

 3- There are NO bent tubes in my mount. there are
 intersecting
 angles but that happens on ALL mounts. At those
 intersections the
 area is beefed up internally. Just because you can't see it
 doesn't mean crap.

 4- I know EXACTLY what it weighs. I don't guess like he
 seems to.
 And it is less then his "estimation"

 5- Of course I beefed up the airframe as I built it. Just
 because I
 didn't state that on my website should not give him a pass
 at a free shot.

 6- Zenith Aircraft seem to be an "issue" to him. Mine  has twice
 the "suggested" HP and still has not broken in half.

 7- The plane has so much power that at cruise I can
 throttle back
 to ALOT.. A 801 has alot of aerodynamic drag. I can run 90@
 6.4 GPH
 or 110@ 17 GPH. The plane hits a brick wall so why burn
 three times
 the fuel to go a little faster. If I wanted to go fast I
 would have
 built another type plane. You would think a guy like him
 could draw
 a simple conclusion.

 8- I have probably built, raced and tested more engines hen
 he can dream about.

 9- BSFC of .45 ???   Jeez. I would be
 embarrased to tune a motor that rich.

 10- Nothing is " seriously wrong"............. I am
 seriously throttled back.

 11- The motor is capable of 600 + Hp in different trim. ie,
 different
 redrive ratio, different intake design, etc. The motor will
 not gain
 any more weight by changing componants, so 350-400 Hp is a
 no brainer..
 On MY plane I purposely stayed with 1.43-1 because it for
 sure doen
 not need any more power.

 12- Where did he get the 3700 RPM #  from ?  I
 turn the motor alot
 higher then that on take off. Yeah, the prop is kinda noisy
 but nothing
 worse then what noise a seaplane makes with a large
 diameter prop.

 13-  """ Totally Clueless"""  Ya wanna bet..

 And in closing all I can add is
 " I am really worried here. Probably one of the most
 dangerous airplanes
 I have seen in a very long time. "

 Geez... Where was he 5 years and 300 hours ago ??????.


 Ben Haas.



 Where are the "facts"?

 What manifold pressure and RPM do you run?
 "Less"? How much less?
 "More"? How much more?
 "ALOT"?

 What is the real BSFC?
 What does the engine weigh?

 At 17 gallons an hour at .40 BSFC giving you the benefit
 of the doubt as far as leaning goes you are seeing
 265 HP max not 400 HP. I can believe 265 HP at 17 gallons
 an hour.

 I don't think you understands what trangulation means.
 Here is the pictures from your web site. Where is the
 diagonal in the first bay?

 How and where did you beef up the fuselage?

 What is the empty weight of the aircraft?

 Paul Lamar


 Spell my name correctly and I might answer your silly questions....
Maybe you can use your nifty cad program to help but chances are you
will get that wrong too, just like designing C. Smiths mount and
calling it FINAL.... And then he emails you back explaining the 640
does NOT have a 5th hard mount point on the top of the fuselage....
You are going to kill another human being one day by your actions ....


Ben Haas  N801BH  Jackson Hole Wy,   JAC  www.haaspowerair.com


I don't care whether you answer my pertinent questions or not. If you can't
discuss the issues attack the messenger or change the subject.

I addressed the fifth mount issue with Mr. Smith but you would not know
that
as  you are not on this list.

There is nothing wrong with running a V8 with aircraft quality
parts at 100 HP continuously if you don't mind the 200 to 300  pound weight
reduction in the payload. Just don't mention the 400 HP which you will
never see with a normal diameter propeller.

The issue is the power to engine weight ratio and the effect the excess
engine weight and consequent required ballast in the tail has on the
structural integrity of the fuselage.

The real reasons you don't answer my questions is you don't want
that information out there. Perhaps you don't know the answers.


Paul Lamar


Civility, Gentlemen. As another 801 builder and auto-conversion convert I
have exchanged email with Mr. Haas, and read many of his posts on the Zenith
forums. He has always impressed me with his original problem-solving skills
and willingness to listen to other opinions. He has always been very
conservative about offering advice to others, acknowledging his plane is a
"one-off" and there may be better ways to do things. He has also been
straightforward with me about performance shortcomings with the 801 in
general and his specifically, even though we've never really met.
Of course I also respect Mr. Lamar's engineering expertise, proof being my
putting a renesis on a Lamar / Hey mount on my 801, not a V6 with a
BeltedAir PSRU as I originally planned.

We all have different goals. I have no intention of ever performing a P-Port
modification, as my goal is to keep the engine as stock as possible. I know
I'm losing power with this decision, and I'm OK with that; different goal. I
respect other builders goals.

BTW, I fitted my wings this past weekend. This let me locate the holes for
the flaperon control arms, my last task for finishing the control systems.
I'm down to the panel and the engine now.

Thanks,
Kenny A.

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.