Subject: "P" port sealing plates
From: Rotary Engine
Date: 9/23/2009, 9:44 AM
To: AAA Put this in the To box


  Kelly Troyer wrote:
  Paul,
    I would like to buy 2 of your "P" port sealing plates............Please
  let me
  know how much and where to send payment.............

  Thanks,
  --
  Kelly Troyer
  "Dyke Delta"_13B ROTARY Engine
  "RWS"_RD1C/EC2/EM2
  "Mistral"_Backplate/Oil Manifold


  Sure no problem. Every body pays cash. No checks or credit cards.
  Ten dollars each. Plus $5 US PO flate rate box.
  send to:

  Suite 303
  830 East Santa Maria St.
  Santa Paula CA
  93060

  We should have some contoured SS tubes any day now to go along with
  that.

  We also have a whole bunch of other bits and pieces for slide throttle
  p-ports.

  Paul Lamar


  Paul,
  Has anyone pressure tested the sealing plates?  If so, what would be an
  adequate pressure to test them.  I'm figuring 45 psi which is 3 X my
  normal
  operating pressure.

  Mark S.

  I was going to suggest 50 psi.

  Paul Lamar


  Sounds good to me.

  Mark

  The beauty of these sealing plates is they are easily repairable if you do
  have a leak.

  If you are talented with a Dremal tool it is possible to put a large
  O-ring
  in there :)

  Paul Lamar


  Paul,
  As long as the RTV does its job, why install an o-ring, belt and
  suspenders?  Where are we talking about putting the o-ring?  How would you
  go about replacing the o-ring if it leaked?  I like the RTV solution
  better
  as you can easily re-do it if it leaks.

  Mark S.

  Just for grins? :)


  The O-ring would go in the joint to seal both out and sideways
  in theory. It is a compound grove so hard to machine even in an
  NC mill.

  Paul Lamar

  Well, I'll know in a couple of days whether my p-ports pass the 50#
  pressure
  test.

  Mark

  I have my fingers crossed :)

  Paul Lamar

 Paul,

 The RTV has had 48 hours to set up, so I fabricated a testing rig and
 pressurized the p-port rotor housings last night after work.  I used 50 psi
 as the test pressure.  The bad news is that all three housings had
 very small pinhole leaks in the vicinity of the welds.  This was obviously
 due to the smoothing and blending of the welds.  That was easy enough to
 fix
 with the TIG and a little more blending and smoothing.

 I also had leaks around the sealing plates on 2 of the 3 housings.  Both
 are
 at the 7-8 o'clock positions and between the plate and the SS tube.  This
 is
 the thinnest area as far as sealing surface is concerned.  I'm thinking
 that
 an o-ring between the plate and SS tube would be a good fix for this.

 Bottom line is for everyone to pressure test their p-port modifications
 before engine assembly.

 Mark

 Thanks for the feedback Mark.

 I'll check into see how much a internal O-ring grove will cost
 in all new sealing blocks. If people wish we will retro fit the blocks
 that people have now. That would be one less area they would need RTV.
 In fact one could buy sheet RTV and use it as a gasket. You would still
 need
 a bit on the threads.

 It is easy enough to pressure test the just section of the rotor housing
 where the weld is with a section of tire tube. Here is how I did it. No
 need to assemble the engine.

 No need for the tubeless tire fitting if you use the section of tire
 tube with the molded in tire valve. Just buy a new tube and cut it
 up.

 Paul Lamar

"Just buy a new tube and cut it up."

That's exactly what I did.  Used a scrap piece 1" x 2" of oak cut to about
6" in length and drilled a hole midway for the stem to poke through.  I used
a second piece of oak and a piece of inner tube to make the seal on the
other side, then clamped it all together.  That worked ok, but the tube gets
thicker around the stem which caused leaks elsewhere.  It needed extra
clamps to get it to seal.  Your method looks better, but I didn't have any
scrap aluminum laying around.

Mark

I was able to get a real fat O-ring in there.
.139 section. This should ease the sealing problem.
I'll be able to retrofit the blocks if people
send them to me. It will increase the price somewhat but
I think maybe only $5 additional.

I still have about 35 so perhaps Jeff can machine the groove.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.