Subject: Motor plate hole lay out
From: Rotary Engine
Date: 9/28/2009, 6:03 AM
To: AAA Put this in the To box


 Paul

 I pulled these numbers off the machine..........check over see if it
 makes sense.... only a couple of holes seem to be right on.....

 The datum for the X is the flat that makes the exhaust and  intake
  side,
 the Y is the oil pan face.....

 jeff

 OK Jeff I'll take a look at it.

 Perhaps a better datum is the center of the e-shaft axis.
 I'll see what I can do.

 Paul Lamar

   Paul

   In the first picture the effective Datum is the E-shaft so these
 numbers
   relative to this are pertinent. I gave both versions for those that
 want
   to take positions of the flat and perpendicular faces.

   jeff

   I see.

   Here is Tracy's polar dwg very carefully converted to rect. 8 places
  or so
   :)
   I think Butch did this with a calculator. Same coordinate system
   as yours (e-shaft center) so we can make a direct comparison. The only
   thing
   we don't have is the exact position of the upper RX8 bolt.


   Paul Lamar



   Jeff, I was wondering if you have a tension bolt- dowell pin - eshaft
  drawing with CMM coordinates for an end housing that you could post. I
  have
  designed side housings for a four or six rotor mazda and only have
 what I
  could measure by triangulating with a 12" dial caliper. I intend to
give
  away the drawings to interested builders and would want the best
 accuracy
  available.

  george grimes


 george

 Yes I have all that..........I am working in on the final hole positions
 for the tracy mounting plate..The dowel pin holes are perfect. One other
 hole is off by about .010 and the RX8 added hole position is not known
 yet until I get a RX8 housing to measure.....

 If I was to send something to you, can you take files as opposed to just
 drawing with all the coordinates????

 If your building side housings, I intend to as well,  I have the
 material here  and looking for the time to get started..maybe we should
 work out something...If it's top secret, I get that....


 jeff

 Jeff I'll check with Mazdatrix on Monday for an RX8 end housing.
 They may have one we can borrow. I'll stop in and pick it up and
bring it
 down on Monday or Tuesday. If that don't work I'll haul down my complete
 RX8 engine. I don't have a digitizer on my cheap chinease mill.

 Paul Lamar


Paul

I would certainly like to meet you. Just let me know for sure when or if
your coming I want make sure I am here...If you could get the housing
from Mazdtrix that would  be the best option.  Hauling your complete
engine down here seems much and am not sure how I would still pull the
coordinates exactly.  setting the engine in the machine would be
difficult ,possible but  difficult........

Let me know your plans....

jeff

OK Jeff I'll check with Mazdatrix on Monday. I amy not get there until
latter in the week. I forgot I had a medical appoint me on Tuesday.

Can your mill take an assembled RX8 engine so we can digitize
some holes in the end housing?

Paul Lamar


Paul

Not sure. I have to stand the engine up and hold it square and solid. My
machine has a total Z of 24 " but the receiver for th pallet changer
takes 6". Figure the tool holder and the E shaft,  could be real
close......Plan B,  my contacts with some companies I do work for have
the equipment to do this easy and I will talk to them tomorrow.

jeff

We could mount it horizontally and get a measurement relative
to the adjacent bolts and the table. Max height is about 14 inches.
Make up some short 10 mm socket head screws with a known
head diameter.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.