Subject: Returnless Fuel -- WAS: CAS Sensors
From: Rotary Engine
Date: 10/12/2009, 7:49 PM
To: AAA Put this in the To box


Vince,

That is one reason I like using Digikey, to make sure I can get the
parts! I also made sure the parts my company makes are available
from Digikey, as I've run into engineers who design stuff by seeing
what is available and ships overnight.  THe Digikey warehouse is a
cool trip on how things are done (online order entered to completed
box dropping in the shipping bin in something like 9 minutes!).

Napa, at one time, had a 'electrical catalog' where you could just
scan down the book looking at photo's.  Not online anymore, as you
have to select vehicle then look.  Most vehicle OEM went to
'returnless' systems to meet evaporative emissions. Less plumping,
less vapors.

With a return line to a small header tank, fuel returning before
the  pump, you can retain the older pressure regulator. There is a myth
that 'fuel gets too hot' yet, when measured we were within one
degree! Aluminum fuel line, aluminum header tank disappate heat, so
the "hot fuel" doesn't really exist, but always reported!  I have
high wings, both gravity feed to a  common Andair R-L-Both-Off Valve.

With a return loop system, the fuel regulator is engine vacuum
modulated, less software to modify the injector pulse width (if you
hold a constant fuel rail pressure and engine vacuum changes, you
need to modify the fuel pulse width to compenstate for the pressure
differential. Happens too fast to modify fuel pressure... hence why
the Ford Engine controller uses a floating point unit!With
MATLAB  we did some cool demo's on modifying the fuel/spark on a cylinder
per cylinder basis... which is part of the reason for eTPU (Time
Proccessing Unit)controllers built into the uC.

Tom

Tom -

The goal of the Returnless PWM Fuel Pump Controller project isn't to
reduce fuel temperature.  It is to:
1) simplify fuel line installation
2) provide redundant fuel pumps
3) reduce electrical load
4) lengthen pump life
5) provide all-electric tank selectors

Regarding the constant fuel rail pressure: I don't think fuel
pressure variations will be a factor.  We will be making far fewer throttle
changes than auto applications, and we'll be adjusting our mixture
manually.  Additionally, I think fuel pressure and flow can be
adjusted very quickly with the PWM approach - certainly one of the
tests I should run.

I haven't decided on the importance of keeping fuel pressure stable
relative to MAP.  However, I think it is a valid discussion point for
the group.

The Motorcraft FRPS (Fuel Rail Pressure Sensor) does have a manifold
vacuum port to indicate pressure readings relative to MAP.  My
research indicates that this is a failure mode of the FRPS: when the
diaphragm blows, raw fuel gets sucked into the manifold.

-Vince Orton


Hi Vince
 The fuel pressure is indexed to the manifold pressure to maintain a fixed
differential. At idle the vaccum is high thus low pressure. Wide open
throttle gives high manifold pressure. This is mandatory to keep the
injection volume and spray correct.
 I also Googled transducer manufacturers and the top site was IQS
Directory. There is a whole list there.
 In addition to the Wika I have seen Noshok. Try 630C,650 pressure. They
also have the 800 temp.
 Barksdale 600 series; possible part #'s 423H3-04 or 423H4-04. I have used
some Barksdale items and they were less expensive.
 GP:50, no experience with them.
 Trans Metrics; for United Electric Controls - TX-200. Again no experience
with them.

 Dale Davies


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.