Subject: slide throttle and SS P-port fab partts and shipping addresses.
From: Rotary Engine
Date: 10/20/2009, 11:02 AM
To: AAA Put this in the To box


 Paul,

 Who would I contact to order a slide throttle and SS p-port installation.

 Again, I 've been out of the loop for awhile and alot of recent talk pertains

 to the RX8 engine with regard to slide throttle and SS p-port fab.

 Are these parts compatable with my 2nd gen 13B



 Thanks,Geir Andersen

 You can buy the slide throttle kit parts from me. The prices are on the
 web site. No checks no CC's, or money orders. Cash green backs only.
 You will still need to buy .032 thick Teflon from McMaster Carr or Scientific
 Commodities in Lake Havasu that runs about $28.00 a sheet.

 Rotary housings are pretty easy to do yourself if you have access to a mill.

 Right now we are in the process of doing a group buy on p-port rotor housings.
 When ten people have sent us their rotor housings we will set up the mill,
 bore the holes, tig weld in SS tubes and bolt on a sealing plate on the outside.
 You will need to finish the inside with a Dremel tool sander.

 Cost for that service is $150 each... cash only, no checks, no money orders.
 Plus shipping cost back to you.

 We will let you know when we are ready to ship and then you can send
 the money. Check the rotor housings width for shrinkage. You will need a 3 inch
 to 4 inch micrometer. You can get a low cost version at Harbor Freight.

 Shrinkage is a sign of a severely over heated engine making the rotor housings
 useless. We see much less of this since Mazda changed the alloy about 20 years ago.

 We currently have six so we need four more to get started. Then we will wait for
 another ten.

 Shipping address for rotor housings is:

 Paul Lamar C/O
 Light Speed Engineering
 416 E. Santa Maria Street,
 Hangar #15, Santa Paula, CA 93060


 Mailing address for all other part orders is:

 Paul Lamar
 830 East Santa Maria St.
 Suite 303
 Santa Paula, CA
 930060

 For more info see:
 http://www.youtube.com/profile?user=UTUBPLEASE#p/u/24/LkKw72dZ2yc
 http://www.youtube.com/profile?user=UTUBPLEASE#p/u/39/KQL45DYgIFw

 http://www.rotaryeng.net/Mazda_R26B_US.pdf
 http://www.rotaryeng.net/intake.html


 Paul Lamar

 Thanks Paul

 What is the benefit of the RX8 with ,I believe side port exhaust to the 2nd gen I have

 Geir Andersen

 The side exhaust makes the RX8 p-port equivalent to an ordinary 13B as far as port
 timing is concerned. That gives it a better idle. The side exhaust also
 is a couple of hundred degrees F cooler so the muffler does not catch
 quite so much hell.

 Paul Lamar


     Just to confirm, The PP intake timing is the same on both 2nd gen and RX8 housings regardless of exhaust port configuration.



Thanks Geir Andersen

It is the same.
Port timing is not at all critical for our application. It could be for
racing were every .1 HP counts.

Runner length is far more sensitive. The optimum is around 22 inches.
Runner diameter is also important. 1-7/8 ID seems to work well.
HP will be around 250 at 7500 RPM.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.