Paul,
Who would I contact to order a slide throttle and SS p-port installation.
Again, I 've been out of the loop for awhile and alot of recent talk pertains
to the RX8 engine with regard to slide throttle and SS p-port fab.
Are these parts compatable with my 2nd gen 13B
Thanks,Geir Andersen
You can buy the slide throttle kit parts from me. The prices are on the
web site. No checks no CC's, or money orders. Cash green backs only.
You will still need to buy .032 thick Teflon from McMaster Carr or Scientific
Commodities in Lake Havasu that runs about $28.00 a sheet.
Rotary housings are pretty easy to do yourself if you have access to a mill.
Right now we are in the process of doing a group buy on p-port rotor housings.
When ten people have sent us their rotor housings we will set up the mill,
bore the holes, tig weld in SS tubes and bolt on a sealing plate on the outside.
You will need to finish the inside with a Dremel tool sander.
Cost for that service is $150 each... cash only, no checks, no money orders.
Plus shipping cost back to you.
We will let you know when we are ready to ship and then you can send
the money. Check the rotor housings width for shrinkage. You will need a 3 inch
to 4 inch micrometer. You can get a low cost version at Harbor Freight.
Shrinkage is a sign of a severely over heated engine making the rotor housings
useless. We see much less of this since Mazda changed the alloy about 20 years ago.
We currently have six so we need four more to get started. Then we will wait for
another ten.
Shipping address for rotor housings is:
Paul Lamar C/O
Light Speed Engineering
416 E. Santa Maria Street,
Hangar #15, Santa Paula, CA 93060
Mailing address for all other part orders is:
Paul Lamar
830 East Santa Maria St.
Suite 303
Santa Paula, CA
930060
For more info see:
http://www.youtube.com/profile?user=UTUBPLEASE#p/u/24/LkKw72dZ2yc
http://www.youtube.com/profile?user=UTUBPLEASE#p/u/39/KQL45DYgIFw
http://www.rotaryeng.net/Mazda_R26B_US.pdf
http://www.rotaryeng.net/intake.html
Paul Lamar
Thanks Paul
What is the benefit of the RX8 with ,I believe side port exhaust to the 2nd gen I have
Geir Andersen
The side exhaust makes the RX8 p-port equivalent to an ordinary 13B as far as port
timing is concerned. That gives it a better idle. The side exhaust also
is a couple of hundred degrees F cooler so the muffler does not catch
quite so much hell.
Paul Lamar
Just to confirm, The PP intake timing is the same on both 2nd gen and RX8 housings regardless of
exhaust port configuration.
Thanks Geir Andersen
It is the same.
Port timing is not at all critical for our application. It could be for
racing were every .1 HP counts.
Runner length is far more sensitive. The optimum is around 22 inches.
Runner diameter is also important. 1-7/8 ID seems to work well.
HP will be around 250 at 7500 RPM.
Paul Lamar
Paul
Is runner length important at all when running a turbo? Or does boost
negate the benefits of the Length... Also, for a turbo application
where would the best location be for the injectors... I'm thinking
right near the Intercooler.
Mike C.
You know that is a good question. I think Mazda uses a tuned length with the
turbos so the BSFC is better when cruising off boost.
It does not however appear to hurt the top HP as late model stock 3rd gen turbos
had 280 HP.
Jim Mederer used tuned length runners in his 1200 hp 3 rotor turbo.
Lately these things are putting out 1400 HP.
http://www.rotaryeng.net/dyno3rot.jpg
I would do something like this only with two runners instead of 4. In theory
it reduces the pressure drop through the essential intercooler. The mini
cooper uses something similar. Intercooler pressure losses are critical
to BSFC and less so for max HP.
See:
http://www.rotaryeng.net/intake.html scroll down and read "Low Pressure Loss".
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.