Subject: "P" port sealing plates history
From: Rotary Engine
Date: 10/25/2009, 12:28 PM
To: AAA Put this in the To box


 Kelly Troyer wrote:
 Paul,
 I would like to buy 2 of your "P" port sealing
 plates............Please
 let me
 know how much and where to send payment.............
 Thanks,
 --
 Kelly Troyer
 "Dyke Delta"_13B ROTARY Engine
 "RWS"_RD1C/EC2/EM2
 "Mistral"_Backplate/Oil Manifold

 Sure no problem. Every body pays cash. No checks or credit cards.
 Ten dollars each. Plus $5 US PO flate rate box.
 send to:
 Suite 303
 830 East Santa Maria St.
 Santa Paula CA
 93060
 We should have some contoured SS tubes any day now to go along with
 that.
 We also have a whole bunch of other bits and pieces for slide
 throttle
 p-ports.
 Paul Lamar

 Paul,
 What is price of the slide throttle parts and also the contoured
 stainless tubes for
 the P port inlet ?....................
 --
 Kelly Troyer
 "Dyke Delta"_13B ROTARY Engine
 "RWS"_RD1C/EC2/EM2
 "Mistral"_Backplate/Oil Manifold


 Check out the web site bottom of the front page.

 Paul Lamar

What specific purpose does the sealing plate perform.

Are you still sealing the water jacket with JB weld


Thanks ,

GEIR

After some bad experiences with JB Weld and epoxy we came up
with the unlikely idea of welding a SS steel tube directly
to the steel liner. Mark Steitle tried it first and I did
a few more on junk housings. Wonder of wonders it did not
warp the rotor housings. Then I built an RX8 p-port engine
using the welding trick and ran it on the Mazdatrix dyno.
Worked like a charm. Aprox. 250 HP at 7,500 RPM.

Then the issue came up on how we seal
the outer water jacket. The obvious answer is to come up with
something that could be easily resealed if necessary. Hence
the sealing plate is bolted to the side of the engine. You smear
it with red RTV and it is good to 500 F.
                
Mark is the leader here and he discovered most of the RTV leaks
occur around the tube and the sealing plate so I am in the
process of modifying them with O-rings in that area.

BTW you can also use a bead of Red RTV around the inside
of the SS tube and the outer wall of the water jacket with
the sealing plate bolted on and apply air pressure to the water
jacket in that area. The uncured red RTV will squish into the
cavities sealing them. This is also a good idea to check for
pin hole leaks around the finished weld. Easily repaired
BEFORE you assemble the engine.

As a belt and suspenders approach you can also pot the WJ cavity
with Devcon Liquid Aluminum but it will be tedious to repair
if you ever develop a leak later on as all that epoxy will
have to be ground out. You never know if it leaks until
you let the epoxy cure. Not a good cycle. BAD NEWS!!!!

All this is well worth it as you don't have to use all 250
horses during cruise. Fuel burn is directly proportional to the
number of horses you use. It is handy for going fast at 8,000
to 14,000 feet, STOL and good for getting out of high hot.
There is no weight penalty as there would be going from a
four to a six cyl. AC engine.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.