Subject: "P" port sealing plates history
From: Rotary Engine
Date: 10/26/2009, 10:23 AM
To: AAA Put this in the To box


 Kelly Troyer wrote:
 Paul,
 I would like to buy 2 of your "P" port sealing
 plates............Please
 let me
 know how much and where to send payment.............
 Thanks,
 --
 Kelly Troyer
 "Dyke Delta"_13B ROTARY Engine
 "RWS"_RD1C/EC2/EM2
 "Mistral"_Backplate/Oil Manifold

 Sure no problem. Every body pays cash. No checks or credit cards.
 Ten dollars each. Plus $5 US PO flate rate box.
 send to:
 Suite 303
 830 East Santa Maria St.
 Santa Paula CA
 93060
 We should have some contoured SS tubes any day now to go along with
 that.
 We also have a whole bunch of other bits and pieces for slide
 throttle
 p-ports.
 Paul Lamar

 Paul,
 What is price of the slide throttle parts and also the contoured
 stainless tubes for
 the P port inlet ?....................
 --
 Kelly Troyer
 "Dyke Delta"_13B ROTARY Engine
 "RWS"_RD1C/EC2/EM2
 "Mistral"_Backplate/Oil Manifold


 Check out the web site bottom of the front page.

 Paul Lamar

 What specific purpose does the sealing plate perform.

 Are you still sealing the water jacket with JB weld


 Thanks ,

 GEIR

 After some bad experiences with JB Weld and epoxy we came up
 with the unlikely idea of welding a SS steel tube directly
 to the steel liner. Mark Steitle tried it first and I did
 a few more on junk housings. Wonder of wonders it did not
 warp the rotor housings. Then I built an RX8 p-port engine
 using the welding trick and ran it on the Mazdatrix dyno.
 Worked like a charm. Aprox. 250 HP at 7,500 RPM.

 Then the issue came up on how we seal
 the outer water jacket. The obvious answer is to come up with
 something that could be easily resealed if necessary. Hence
 the sealing plate is bolted to the side of the engine. You smear
 it with red RTV and it is good to 500 F.

 Mark is the leader here and he discovered most of the RTV leaks
 occur around the tube and the sealing plate so I am in the
 process of modifying them with O-rings in that area.

 BTW you can also use a bead of Red RTV around the inside
 of the SS tube and the outer wall of the water jacket with
 the sealing plate bolted on and apply air pressure to the water
 jacket in that area. The uncured red RTV will squish into the
 cavities sealing them. This is also a good idea to check for
 pin hole leaks around the finished weld. Easily repaired
 BEFORE you assemble the engine.

 As a belt and suspenders approach you can also pot the WJ cavity
 with Devcon Liquid Aluminum but it will be tedious to repair
 if you ever develop a leak later on as all that epoxy will
 have to be ground out. You never know if it leaks until
 you let the epoxy cure. Not a good cycle. BAD NEWS!!!!

 All this is well worth it as you don't have to use all 250
 horses during cruise. Fuel burn is directly proportional to the
 number of horses you use. It is handy for going fast at 8,000
 to 14,000 feet, STOL and good for getting out of high hot.
 There is no weight penalty as there would be going from a
 four to a six cyl. AC engine.

 Paul Lamar

I dont no what temp the housing is ,adjacent to the welded tube, but I would think the RTV might do
a better job with long term adhesion due to different expansion characteristics of the SS tube and
the aluminum housing. I would think the epoxy might lose its seal with the SS expanding at a
different rate than the aluminum housing.I'm refering to the area just behind the weld,which seems
of more concern incase that weld breaks loose over time.A little RTV may offer just a little
redundancy.

With regard to the benefit of having the extra HP when you need it, nothing scarier than trying to
clear that 50' obstacle at the end of the runway in a 150 on a hot day.Better to be looking at it
than for it. HP



Just wanted to take the opportunity to thank everyone for the input.It amazes me the commitment you
guys have to the Rotary development and after being out of it for a couple years and coming back and
seeing you guys still hard at it is a wonderful thing.Thanks again for your time.



Geir Andersen                   

The temperature in that area is way less than 500 F as it is cooled by the incoming charge.
That sounds like good idea. I need to research the availability of a lower viscosity
pour-able red RTV to fill the whole cavity. I know it is out there as it is used for making molds.
That might work just great. It probably adheres to unprepared (non converted) aluminum better than
epoxy as well. I'll have to test that.

----------------------------------------------------------------------

Well it did not take long. It is sold in Fry's of all places. Probably for
potting electrical devices.

I am thinking the optically clear will allow us to visually inspect for leak locations. Don't fill the cavity to the absolute top and put a little colored water in there and apply air pressure.

Great idea Geir.

I am going to get some and try it on a junk housing. It does require a primer however.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.