Paul- I started my teardown last night after finally getting a second copy of the Turrentine dvd. I'm one step away from cracking the case & seeing what is what. One thing that wasn't in the Turrentine video was how to remove the counterbalance -- in his video there is a flywheel which I believe has an integrated counterbalance, vs the stand-alone one on my engine. In any case - I'm guessing I'll need to use a puller to get it off. I tried to give it a wiggle on my way out the door this morning & it didn't act like it was going to come willingly. Also - will I be able to reuse any of the seals (since the engine has what -- a grand total of 10 hrs on it?) or am I replace everything along the way. Finally - you alluded in an earlier email to new apex seals... Why? Again - the ones in there are Tracy's and only have 10 hrs. Mark Supinski You must be very careful to record the exact position of all the rotor seals. They must go back in the slot they came from. Mark the rotors... rotor one... rotor two. Then mark the apex seal slots on each rotor ...slot one... slot two... slot three. Use marked paper cups to separate all the seal sections so you can get everything back in the exact same place it came from. Take as much time as it takes to do this. This is very very important as seals are adjusted to fit. -------------------------------- A puller will help getting the counter weight off but a tap by a hammer on the outer edge may be all that you need. This sets up vibrations in the counter weight that may free it from the taper. Hopefully you have the front nut off already. ------------------------------------------- You will need new water O-rings so get the Creavey TES versions as they are better than Mazda and reusable. Probably cheaper too. Same goes for the oil O-rings on the sides of the rotors. http://www.creavey.com/ I will outline what we are talking about. There are four coolant sealing O-rings per rotor housing. Two outer and two inner. Two on one side two on the other. If the slots are in the end housings there are two per end housing surface. There are also four oil sealing O-rings per rotor. Two on each side of the rotor proper. These are located on the flanks of the rotor. Two per side. Teflon encapsulated silicone O-rings are the best there is for this application. Teflon is about the most inert material you can find and it is resistant to most known chemicals. Unfortunately it is not rubber like and that is where the high temp silicone rubber core comes into play. http://www.creavey.com/ > 1. Inner coolant oring - > > circumference = 28.625 > diameter = 9.111 > slot depth = 0.062 > slot width = 0.141 > section size = 0.098 > 2. outer coolant oring - > > diameter = 11.340 > slot depth = 0.062 > slot width = 0.110 > section size = 0.093 This is critical! The proper section size is .093. Not 3/32 as a 3/32 O-ring is bigger in section size than .093. The TES O-rings are stiffer than the stock O-rings. It is harder to get them to lie in the groove. Even with Vaseline. When you buy them they don't come flat. I found that using a plywood form to pre set the slightly under size TES O-rings for a few days works well. Here is a picture. -------------------------------------------------------------- Oil O-rings. I checked the installation of the oil O-rings with the new sizes I got from Creavey. They worked perfectly and were very easy to install. You will need a little O-ring lube and a 2 by 8 to install them. They were also easy to remove with no signs of distortion. One of the secrets is if you reuse the old oil scraper rings they must be spotlessly clean inside and out. Soak them in carb cleaner for a few days. If you use new scraper rings this will not be a problem of course. The second thing to watch out for is don't nick the rotor wall between the two scraper rings when you remove them. Very very important!! These can be the same or just a little more than the stock oil O-rings from Mazda. The proper oil O-ring sizes are: 0.093" section 4.68 inch ID 0.118" section 4.33 inch ID I can vouch for the quality of the Creavey O-rings but some of those water TES o-rings from Mcmaster Carr I have seen are not as good. This is not to say they won't work. They just don't look as good around the joints as Creavey O-rings. Viton is good only to 400 degrees F. The center of the rotor runs as high as 500 degrees F. I think 400 degrees F leaves's too little of a safety margin when 500 degrees F is available in TES O-rings at the same price probably. ************************************************************ How-to-measure.txt Here is how to double check my work. We will do a little reverse engineering. The O-ring grooves are two half circles connected by straight sections to form sort of an oval. Measure across from side to side on the end housing to the inner edge of the O-ring groves This then is the inner diameter of the half circle. We will call this dimension SSL. For the inner O-ring this diameter is 7.5" Outer diameter is is 9.75". These form two circles of 23.562 circumference and 30.63 circumference. C = D X Pi (3.1416) Measure the distance up and down to the inner edge of the O-ring grooves. For the inner O-ring groove this dimension is 9.75 (confusingly). Outer o-ring groove is right on 12 inches. We will call this dimension VL for vertical length. VL-SSL gives us the length of the straight sections. We have two straight sections 9.75- 7.5 or 2.25 inches in length for the inner o-ring slot and 12 - 9.75 or 2.25 for the outer O-ring slot straight sections. There fore the inner circumference is 23.562 + 2.25 + 2.25 or 28.062". Close to the number we got below. Divide by 3.1416 to get the equivalent diameter. For the outer o-ring slot the circumference is 30.63 + 2.25 + 2.25 or 35.13. Also close to the number we got below. Now to be real precise you must repeat these measurements for the outer O-ring slot grooves. Or we could merely take these numbers below as the center line numbers or OD numbers. In any event you want to err on the small side as you are going to cut pieces of plywood the exact size of the inside wall of both slots and slip the o-rings over this plywood form for for a few days so they will take a set. Other wise you will play hell getting the o-rings to lie flat in the grooves when you assemble the engine. > > SNIP< > > > > > > You need to do accurate calcs on the cross sectional areas and avoid > > > sealant, altho this may just extrude out of the cracks when heated. The > > > rubber is too strong to easily extrude thru the fine cracks (near zero > crack > > > width) and can crack something if fully trapped. > > > > > > Bill Freeman > I always encourage experimentation when there is something to be gained but > when it comes to sealant for Mazda coolant O-rings, the experiments have > already been done. Use ONLY Hylomar non hardening sealant. > > Tracy Crook > tcrook@rotaryaviation.com > www.rotaryaviation.com I have always thought of rubber, and that includes silicone, as being "compressible". What has been brought home to me after reading Tom's experience is; rubber is no more "compressible" than hydraulic fluid. Bill hit the nail on the head I think. The O-ring was oversize for the slot and in the process of tightening down the tension bolts the hydraulic force of the rubber broke the housing. Bottom line is measure the O-rings you get and don't use anything larger than .093" diameter in the outer slot. As Tracy points out don't use RTV to hold the rings in place as it could harden and add to your problems. Buy the O-rings slightly under size on the big diameter (no more than 5% undersize) and stretch them on a plywood form for a few days before installing them. They will then lie in the slot perfectly as we discovered with Perry's installation. Don't try to stretch the ring by hand or by another method as you could permanently neck them down. Be careful when buying standard 3/32 O-rings sizes as they may be larger in section diameter than .096. They could be as large as .115 or so which is way too large for the outer slot. Apparently standard 3/32 rings work OK in the larger inner slot. Best to buy the O-rings directly from Creavey the manufacturer. In most case the prices are lower than what Mazda charges for lower temp stock O-rings. Here is a part of their catalog again showing the small increments in section diameter that they sell. http://www.creavey.com/ Take your time and double check your work. Paul Lamar ...No rotor no motor. The Rotary Engine NewsLetter. Powered by Linux. ACRE NL web site. http://www.rotaryeng.net Copyright 1998-2006 All world wide rights reserved.