Subject: Barry bushings installed on Jeff's MM Plate
From: Rotary Engine
Date: 11/3/2009, 5:36 AM
To: AAA Put this in the To box


 Another tidbit of info.

 Paul Lamar


 Paul

 you got me worried, is this good or bad???????????


 jeff

 They fit perfectly. You did a great job. The 1/2 inch bolt is supposed
 to compress the rubber a bit. New bushings come with a large steel
 washer that goes on top.

 Paul Lamar

 Wheeeeeeeewww....................!!!!!!

 Jeff

 Here is just about everything partially assembled on a p-port RX8
 engine.

 Paul Lamar

 Looks very nice. Are you planing on having the intake runners leaned
 over
 like in the last few pics? Seems like getting a fuel rail attached
 would be a RPITA. Is that the engine that's going in your never
 ending project
 plane?

 Vlad

 If you lean over the tubes to give more room under the cowl you can
 rotate the injectors holders so all injectors line up for one fuel
 rail.

 BTW the tubes have not been cut to the proper length yet.

 Also Jeff has not sent me the new spacers yet. What is shown is a
 couple
 of Tracy's spacer blocks.

 Paul Lamar


 I will be sending the spacers to all as soon as I get back in
 town......The round rod spacers will be like TC but the block spacer
 will look like this.....and weight much less..........

 jeff


 That is real cool looking Jeff.

 Paul Lamar
 --

 Jeff,

 I bet you could sell a bunch of lightweight spacers to the rest of
 us.  What
 do you say?

 Mark S.

 I agree! That could be a big seller as no need to change your existing
 motor mount.

 Actually the same thing could be said about the adapter plate. You
 don't need to use the motor mount part. Just saw it off and save some
 weight over Tracy's plate.

 Paul Lamar



 I could make light weight spacer for all.. Just would like to know how
 much interest is out there..The idea of cutting the pate down is like
 hearing finger nails on the chalk board.  If there is a need for
 plates
 more like TC, make them and tell Tracy to leave it out of his kit with
 the appropriate reduction..


 Seem like there is areal need for decent water pump housing, OEM is a
 real clunker....

 jeff

 There is a limited market for cut down motor plates with no motor
 mounts.
 My guess you will find less than five people willing to spend $250
 to take
 out 2 or 3 pounds out of a flying example.

 We need things with a higher priority than water pumps. The 2nd gen
 and 3rd gen engines
 will become more scarce as times goes on and the RX8 pump is fine as
 is.
 Also there is a light weight low cost aluminum cartridge already
 available for the 2nd gen and 3rd gen pumps.

 Now 15 pounds out of the gear box with a $1000 dollar saving is
 another matter :)

 Paul Lamar

Could always revisit the aluminum end and intermediate housings with
steel wear surfaces idea.  Jabiru is machining their entire engine.
Richard Sohn has already proved the approach works.  Of course, with
RX8 housings the exhaust would be a challenge...

Chris  Cosman

That is not what I had in mind. I was talking about a new gear box with way
less technical risk. The market would be much larger than for an aluminum
end housing.


Paul Lamar.

Paul,

Design it to be able to handle enough hp for a turbo p-port 20B.  ;-0

Mark S.

Wood, glass composite or carbon fiber prop only.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.