Subject: 20B Mods: Rotors, Water Pump, Front Cover
From: Rotary Engine
Date: 11/4/2009, 4:29 PM
To: AAA Put this in the To box



When I disassembled my 20B last week, I was  pleased that  all the rotor
housings were in good shape and there was no evidence of overheating.  All
apex seals moved freely and I didn't see any significant problems except
one......The front side housing had a spot the size of a dime that was
deeply pitted as if a single drop of water sat on the iron for a long time
causing it to rust and pit, although there wasn't any rust.  I'm not
comfortable reusing it, so I'm going to get a new one !!!  So the question
arises....since I have to replace it anyway, should I just get a new 20B
front side housing and modify the water pump (which is still a big heavy
beast), or is it possible to just use another parts combination?  In
addition, I would also really like to use the RX8 Rotors if they will work
because they are lighter and have a 10:1 compression which would be great
for my normally aspirated application?....

I remember   recently reading a post from someone in this Group who is
building a  20B  with RX-8 Rotors, Front Cover, Water Pump and CAS.  I
remember
him making the statement that the RX8 CAS is much better  (but I  don't
know
why that is).  Paul, do  you know who that was and if  he has been
successful
at making everything work?  And what is  better about the  RX8  CAS?

Thanks,
Don

I think you can   use a 3rd gen RX7 front housing. Maybe even a RX8 front
housing.  Check
with Mazdatrix on that. They sell them as well. Ask them about  the RX8
rotors while you
are at it and report back what  they  say.

562-426-7960 For Parts Ordering, and General  info
562-426-4460  For Local Service and Parts

Paul Lamar
--


OK, I'll try to give them a call  sometime soon.
Do you have any idea about the RX8   CAS?
Don


Yes it is very simple. We have fooled  with them a lot.
Here are a couple of pictures of Mark's  installation on his
3 rotor of the RX8 sensor.

A hall  Effect sensor does the same thing and it is a lot cheaper.

Also  a ABS sensor will also work the same and it is only $16 at Pep  Boys.

What kind of EFI system are you  planning?


Paul Lamar

Paul,

The bracket shown  in the attached pictures didn't work.  Turns out the CAS
bracket needs  to be made of non-ferrous material, not 4130 as I did.  Once
 I
duplicated the bracket in aluminum, the CAS signal cleared up.  Who  would
have thought???

Mark S.

Mark,
Are you the one who is using the RX8 rotors in a 20B?
If so, did you have any problems?
Don


Don,

Yes, that was me, but I think I've changed my mind about the benefits of
using RX-8 rotors.  Cost is a big factor,, unless you need new rotors
anyway, then you'll need to find someone to re-balance the rotating assy for
you.

From the recent comments on this list, I'm questioning the benefits of using
Renesis rotors.  As far as them fitting and working in a 20b, that doesn't
seem to be a problem.  Paul ran the numbers recently and came to the
conclusion that the Renesis apex seals would work, so you wouldn't need to
cut the apex grooves to use 13b apex seals for use on a p-ported 20b.  So
that hurdle seems to be gone.

There's a third oil seal that I was told to leave out as it is only used on
the Renesis.  The other two oil seals appear to be the same as the 13b/20B.

Mark S.


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.