Subject: 20B Overhaul -water pump
From: Rotary Engine
Date: 11/4/2009, 5:17 PM
To: AAA Put this in the To box



3) Anyone know parts numbers for the water and oil pumps from the 20B or
maybe a supplier you've used that caries them?

Jay


Hi Jay;
   From what little I remember, the 20B's were somewhere between 2nd and
3rd gen.
A good place for used parts and information is rx7club.com.  See also
nopistons.com
There are several forums you can search or post a want to buy thread:
     http://www.rx7club.com/forumdisplay.php?f=95
     http://www.rx7club.com/forumdisplay.php?f=99

     http://www.mazdamotorsports.com

You can supposedly still order Cosmo/20B parts through your Mazda
dealer.  Some people seem to have a full Cosmo parts fiche.  See this
thread for hints (I should have bought that car):
     http://www.rx7club.com/showthread.php?t=788077&highlight=cosmo

Some of the engine parts are here:
     http://cp_www.tripod.com/rotary/pg20.htm
Cosmo:
     http://cp_www.tripod.com/rotary/pg09.htm

possibly:
    http://www.partsnet.com.au/members.html

Cheers
Cary

Paul,
Here are some photos of the original water pump and housing side by side
with the one I got from Atkins. I also included one of the front end
housing. The oil pump is going to fit. So for now I'm just dealing with the
water pump issue. Dan at Atkins suggested an 86'-91' pump and housing would
fit the 20B without any fabricating or cutting. Can you corroborate this?

Thanks
Jay

Your original pump is fine Jay. No need for the 3rd gen cartridge besides
the
that fact that it does not fit the 20B water pump housing. I'll take a
closer look at my
20B out in the hangar and see if I can find any disadvantages to sticking
with the
original pump.

You may have to cut it down to fit under your cowl but that would be true of
a 2nd or
3rd gen water pump housing as well.

Paul Lamar

The front cover looks unique to the 20B but I am not sure. Mainly in the
area of the oil
drain back for the sequentially turbos.


Please take a picture of the front cover both from the front and rear so we
can tell if
it will fit a 2nd gen water pump housings. Also please take a picture of the
20B front
end housing from the front.

The cartridge Dave Atkins sent you is a 2nd gen 8 bolt version. In order to
use that you
would need a 2nd gen water pump housing which may or may not fit your front
cover.

The only drawback I can see  sticking with the 20B WP pump is the difficulty
in finding
a new cartridge if it develops a leak or the bearings go out. They can be
pressed apart
and the bearings replaced but that is what most people don't do. They just
replace the
cartridge.

Paul Lamar


Here are those pics of the front end housing and front cover you requested
Paul. Thanks in advance for taking the time to look them over.

Jay


Thanks for the pictures Jay.

OK I see a the problem with using the 3rd gen front end housing. The tension bolt holes are not all the way through. They must be drilled and spot faced as Steve mentioned. The 3rd gen front cover looks like it will work and as Mark says an RX8 front cover will work with modifications. The water in and out of the block passages look larger but I could be wrong about that so a 2nd gen, 3rd gen  or RX8 water pump may not flow as much water.

The front cover looks pretty much the same as a 2nd gen front cover except for the turbo oil drain back fitting so a second gen front cover should fit and work. Mark says the cut off RX8 all aluminum water pump works so that is a good option to save a lot of weight.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.