3) Anyone know parts numbers for the water and oil pumps from the 20B or
maybe a supplier you've used that caries them?
Jay
Hi Jay;
From what little I remember, the 20B's were somewhere between 2nd and
3rd gen.
A good place for used parts and information is rx7club.com. See also
nopistons.com
There are several forums you can search or post a want to buy thread:
http://www.rx7club.com/forumdisplay.php?f=95
http://www.rx7club.com/forumdisplay.php?f=99
http://www.mazdamotorsports.com
You can supposedly still order Cosmo/20B parts through your Mazda
dealer. Some people seem to have a full Cosmo parts fiche. See this
thread for hints (I should have bought that car):
http://www.rx7club.com/showthread.php?t=788077&highlight=cosmo
Some of the engine parts are here:
http://cp_www.tripod.com/rotary/pg20.htm
Cosmo:
http://cp_www.tripod.com/rotary/pg09.htm
possibly:
http://www.partsnet.com.au/members.html
Cheers
Cary
Paul,
Here are some photos of the original water pump and housing side by side
with the one I got from Atkins. I also included one of the front end
housing. The oil pump is going to fit. So for now I'm just dealing
with the
water pump issue. Dan at Atkins suggested an 86'-91' pump and housing
would
fit the 20B without any fabricating or cutting. Can you corroborate this?
Thanks
Jay
Your original pump is fine Jay. No need for the 3rd gen cartridge besides
the
that fact that it does not fit the 20B water pump housing. I'll take a
closer look at my
20B out in the hangar and see if I can find any disadvantages to sticking
with the
original pump.
You may have to cut it down to fit under your cowl but that would be true
of a 2nd or
3rd gen water pump housing as well.
Paul Lamar
The front cover looks unique to the 20B but I am not sure. Mainly in the
area of the oil drain back for the sequentially turbos.
Please take a picture of the front cover both from the front and rear
so we
can tell if it will fit a 2nd gen water pump housings. Also please take a
picture of the 20B front end housing from the front.
The cartridge Dave Atkins sent you is a 2nd gen 8 bolt version. In
order to
use that you would need a 2nd gen water pump housing which may or may not
fit your front cover.
The only drawback I can see sticking with the 20B WP pump is the
difficulty in finding a new cartridge if it develops a leak or the
bearings
go out. They can be pressed apart and the bearings replaced but that
is what
most people don't do. They just replace the cartridge.
Paul Lamar
Paul,
The 13b water pump housing will fit on the 20b, but the 13b's impeller is
smaller. Also, the Renesis water pump (removed from the front cover)
will
also fit the 20b. The Renesis entire front cover will fit, but it
requires
some machine work for it to clear the 20b front counterweight which
is larger than the Renesis' counterweight and it interferes with some
of the
front cover casting. If you machine it for adequate clearance, then
you are
into the bolt head recesses which then must be welded up, but by this
point,
we're probably beyond what most people would be willing to do for the
limited benefits of the Renesis front cover. Also, the Renesis front
cover
has a different shape and spacing around the oil pan. Not a problem if
you're building a custom oil pan anyway. The easiest route is to cut the
Renesis pump housing from the front cover (if you want to run the Renesis
water pump).
Who was it that commented about removing and replacing the 20b exhaust
inserts. Having gone down that road, my recommendation is DON"T DO IT
unless you're planning on turbo-charging your engine. I changed out
the 20b
exhaust inserts for 13b turbo inserts. Now I'm pulling my hair out
trying
to get a muffler that will handle the torture of the rotary's exhaust and
still quiet things down. Word has it that the splitter inserts are good
for a 5db noise reduction. I constantly get the comment from people that
they can hear me coming long before they can see me. Not exactly the
image
I want to portray. You can be sure that my new engine will retain the
stock
exhaust inserts.
Mark S.
Are you talking about removing the RX8 engine water pump housing <<
from the RX8 engine front cover? In other words sawing it off? That
sounds like a good idea except for the cost of an RX8 front cover. Any
idea what a new RX8 engine front cover costs?
The RX8 WP cartridge will not fit the 20B water pump housing.
Paul Lamar
I've seen RX8 front covers for $30? on ebay. IIRC, There was one
earlier in the week for $75.
For Mark,
Are you Mark Supinski or Mark Steitle? (excuse the my bad memory or
mispelling)
Regarding the 20B exhaust inserts - I think that was me, sort of.
I have a vague memory that the 20B exhaust is more restrictive than the
13B. People have swapped out the inserts or just used 13B housings as
the 20B housings are less common anyways.
Turbos quiet the exhaust considerably while they last. Inserts also
smooth out the flow and may help turbos live longer as well. Turbos a
little downstream would also help. <hint
http://foxed.ca/rx7manual/manuals/Training%20Manual/4._Fuel_&_Emission_Control_Systems.pdf;
p18
For an NA, the NA inserts are worth 7-8db IIRC (which is a LOT, sorry
can't remember the source) and help keep the exhaust stack together
longer. You can port the exhaust port and keep the NA inserts for the
significant noise reduction. A rounded earlier opening should help with
the port open sound bite (Lynn might have numbers). A rounded later
closing would help with increased flow at high output and soften the
apex landing.
There are lots of exhaust sound reduction tricks, some light and cheap.
Lynn has posted loads of info in various places.
BTW, I have an GSL-SE NA car with a Racing Beat exhaust (no pre-silencer
or inserts), it always sounds like it has a hole in the exhaust. I need
to testbed a few sound reduction ideas there too!
Cheers
Cary
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.