Subject: exhaust Inserts and housing temperature equalization.
From: Rotary Engine
Date: 11/7/2009, 5:58 PM
To: AAA Put this in the To box


 Regarding the 20B exhaust inserts - I think that was me, sort of.
 I have a vague memory that the 20B exhaust is more restrictive than the
 13B.   People have swapped out the inserts or just used 13B housings as
 the 20B housings are less common anyways.
 Turbos quiet the exhaust considerably while they last.  Inserts also
 smooth out the flow and may help turbos live longer as well.  Turbos a
 little downstream would also help. <hint




http://foxed.ca/rx7manual/manuals/Training%20Manual/4._Fuel_&_Emission_Control_Systems.pdf
 ;
 p18
 For an NA, the NA inserts are worth 7-8db IIRC (which is a LOT, sorry
 can't remember the source) and help keep the exhaust stack together
 longer.  You can port the exhaust port and keep the NA inserts for the
 significant noise reduction.  A rounded earlier opening should help with
 the port open sound bite (Lynn might have numbers).  A rounded later
 closing would help with increased flow at high output and soften the
 apex landing.
 There are lots of exhaust sound reduction tricks, some light and cheap.
 Lynn has posted loads of info in various places.

 BTW, I have an GSL-SE NA car with a Racing Beat exhaust (no pre-silencer
 or inserts), it always sounds like it has a hole in the exhaust.  I need
 to testbed a few sound reduction ideas there too!

 Cheers
 Cary




Cary,

I didn't hear about the DB reduction until I had changed my exhaust inserts
to turbo inserts.  Then someone mentioned that they would cost me about 5db
and wouldn't add any noticable power.  I didn't realize how loud these
engines can be and how difficult it would be to get my engine quiet enough
to live with.  This things overpowers my Lightspeed ANR headset...
amazing.

The thing I don't like about the 20b exhaust splitters is that they have a
passage through them for an EGR (my guess) system which we don't need.  I
will try to close these on my new engine, either through welding them up or
smashing them closed.  I don't want the hot exhaust gasses passing up
through the engine and heating up the side housings.

Mark Steitle

You don't want your engine to turn into a banana either. The exhuast heat
is designed to
equalize the temperature between the cold side and the hot side.

IMHO everybody should keep a copy of Yamamoto's book "Rotary Engine" on the
nightstand
and read it each night before they go to sleep.

http://foxed.ca/foxed/index.php?page=rx7manual

---------------------------------------------------------------------

More info. You will block off the EGR passages at the exit on the top of
the center housing. Turbo engines already have a cast in blockage at this
location. This is where the EGR valve normally resides.


Paul Lamar



Paul,

As many times as you've posted those figures it has never dawned on me that
the exhaust passages served any other purpose than to channel exhaust gasses
to the EGR valve.  And since airplanes don't need EGR systems, I never gave
it much thought. I guess I'll leave them alone as I surely don't want a
banana powering my airplane.

With that said, my current engine has the turbo inserts install (no EGR
passages) and in 150 hours of Texas flying, I haven't had a problems with
the engine "going bananas" on me.  I guess I'm just lucky.

Thanks,

Mark S.

The term banana shape is an exaggeration of course.
You probably won't notice it but the side seals get a larger workout moving in and out as the rotor rotates in an asymmetric chamber. Worst case the rotor it self comes in contact with the side housing. Also the plug or corner seal at the ends of the apex seal moves in and out as the rotor rotates. At high RPM it could float or stick and lose a bit of compression. In the RX8 engine these parts are coated with DLC to reduce the friction with the side housings and the bore in the rotor so the seal can move in an out more freely. In any event  an even temperature engine will have less wear on the end housings and the side and corner seals.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.