Subject: this may be what we are looking for
From: Rotary Engine
Date: 11/7/2009, 5:40 PM
To: AAA Put this in the To box


  http://www.sae.org/mags/AEI/6906




http://www.freescale.com/webapp/sps/site/application.jsp?code=APLSMALLENGCTRL&tid=vansmallengine



  http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KIT33812ECUEVME
  http://www.freescale.com/support

  C. Smith

  I'll second that. In the true spirit of the 555 one computer per
  injector.
  If we can get this to work it will be off the shelf ignition and EFI
  at very low cost indeed.  Modular and redundant for safety.

  For a two rotor, four FreeScale demo PC boards would be required as
  each one has an injector driver. Two triggers are no problem for us
  as each rotor fires once per rev. Just like a one cylinder two cycle
  piston engine.

  Hopefully there is a one cylinder 2 cycle piston engine FreeScale
  software example that we can use to get a fast start.

  I downloaded a bunch of stuff and got this version of the code
  warrier up and running. Do we have any C programmers on here?

  FreeScale makes you jump through a lot of hoops as far as
  registering and activation which is a real pain in the ass. I called
  them and tried to explain I don't run windows on the Internet for
  virus reasons so on-line activation does not work for me.

  Thanks Craig for letting me know about this.

  Paul Lamar


  Robin's Mac OS disk should have X Code on it, provided it's not too
  old.  You can program C, C++ , and a variety of others with it.

  I just loaded mine for a college course in C++.

  Chris Cosman

  This is a good project for you Chris.

  Paul Lamar

  It would be a great project for me.  However, if you folks were
  expecting any timely results, I may let you down...
  Let me get through my class first and see what I know...

  Chris C.

  OK Chris. C is pretty dry and this should add some incentive.
  Plus you could ask the instructor questions. Code Warrior comes with
  a C compiler.

  Paul Lamar

  What are the questions I need to be asking the instructor.  He wrote
  the book we're using and used to design spy satellites, I'm sure he
  could walk me through this...

  My apologies I haven't been paying too much attention to this thread,
  until now.

  Chris Cosman

  Down load the software and print out some of the C examples.
  If there is something you don't understand ask him.


  Paul Lamar

  Paul, I used to program in fortran, pil, sindue, mad and read up on the C
  and later C++ back in 1999.  As with other languages the programer writes
  his code including things tagged rem (remember what this does) statements.
  Function  blocks are written in sections and when all are ready they are
  "linked" and "compiled" to generate an "executable" file which is what we
  get when we buy software. During the compile stage all the rem statements
  are dropped and all named variables cas maf ign inj that you used are
  converted  to generic equivalents. The executable file can be decompiled
  for
  modification to add mass airflow functions, however not having real
  variable
  names, and all the blocks would still be linked makes a large confusing
  mess
  to sort thru. If you have the original source code (open source) a function
  of conditional statements to convert the floating point mass air flow value
  to an offset of the fuel table would seem to alter mixture. The array of
  data for fuel flow time would have the "name" sub x changed to "name" sub(x
  +offset)Expanding on this for manual mixture overide would be "name" sub
  (x+offset+manual change)

  There are several versions of C++ available. Two of the beter ones
  are microsoft C as used in windows and borland C++  It is generally thought
  that the automatic debugging during linking is much better in borland
  C++During your code writing you have a lot of C in where you send
  variables into a function block and C out where variable values go out to
  other parts of the program. If for instance you send in an integer value
  but
  declare it floating point as it enters the function block and it is output
  with the original variable name with the new value you have a  floating
  point defined an an integer(no decimal point) and an error. The debugger
  looks for these and functions linked to the wrong addresses and changes
  them
  as necessary. The documentation of borland C++ is more informative allowing
  the original intent of the code to be obtained. The new code can then be
  run
  thru the microsoft compiler to make the executable file if you preffer.


  To write source code an understanding of high school algebra is
  essential and secondly conditional statements will be neccessary.
  Conditional statements aresomething is greater than, less than, or equal
  to something else and based on this decision you "go to" some line and do
  something.  For a beginning "the C++ for dummies" book is usefull and a
  full
  version of C++ manual might be usefull if you read it twice.  All the
  sending to and retrieving from a particular storage address type of
  initialization is done in the compiler. Personally I found it usefull to
  write out a line in plane english then converting to code. For instance, if
  the mass air flow voltag e is more than this but less than that and the air
  temperature is more than
  this and less than that then enter a fuel flow time of something in an
  array
  named whatever on a line number some variable plus 1 then go back and
  repeat
  with the mass airflow a step higher until the mass air flow is more than
  some number, then start over with the air temperature one step higher until
  some value is exceeded then exit this function. This would generate an
  array
  (look up table) for fuel versus air. A more extensive set of inputs
  including throttle position and crank angle sensor position and rpm for a
  single master table would generate a larger table. By using rpm as the
  input
  the table would sort thru the list  to choose fuel flow time and injection
  and ignition timing. Using multiple tables or branched tables would reduce
  sort time, and using a polar array as a matrix could be a nice trick to
  cross refference many tables in a single sort. We did this to sort lumber
  by
  length, width, thickness, grade, species, trimmed, untrimmed, current bin
  location etcetera for lumber sorting/packaging systems.


  About using a pre built board without mass air flow or some kind of
  air density input I don't understand how to input data on a board with no
  input treminal to connect to. Using a second board with a sata or serial
  connection would add more circuit boards and this is then starting to look
  like an industrial rack system. Is it possible to match up a  mass air flow
  sensor output to replace one of the existing inputs to the board, possibly
  the throttle position sensor if a manual throtttle cable is used for power
  control. I was thinking the ford maf sensor could be in series with a pot
  to
  modify the voltage and  add manual mxture override.

  george grimes


  The Code Warrior comes with a C compiler debugger and emulator. All free.
  The boards have .025 square headers on the opposite side for data input.

  We think there is already a provision for a mass air flow sensor input. It
  would help if you downloaded the free code samples and see if there is a
  sample C program source we can use already written. Just about any one
  cylinder program will work.

  Paul Lamar

  The MC9S12P128 has a 10ch 12bit a/d, so a great many possiblities exist for
  input. Download

  http://www.freescale.com/files/analog/doc/user_guide/KT33812ECUUG.pdf?fpsp=1

  I don't know as of yet if the sample application has provision for MAF, but
  there is some pre cut smples for demonstration and application validation.
  I
  would think it may be as simple as substituting one input for another, some
  scaling math?, and maybe creation of look-up tables.
  C. Smith

  Paul, pages 31 and 42 user guide show the locaton of the manifold absolue
  pressure
  inputs which  could be retained or switched to maf. The look up tables are
  user defined so the nonlinearity of maf  or air temp sensors would be done
  on the included spreadsheet of the kit software. Has anybody got the kit
  price and price for additional boards. I haven't used my oscilliscope for
  decades, but it could be a  fun winter
  project.
  george grimes

  I see what you are saying. A MAP sensor is a lot cheaper than a mass
  airflow sensor.
  Cheap enough to use one for each rotor. Like $10. There is also a throttle
  position sensor which would help the throttle response.

  Here is the diagram from page 31. It also looks like it has a missing tooth
  detector from the crank angle sensor.

  Paul Lamar

  Yes, missing tooth is the scheme they are using in the validation. The more
  I look at this, the better it looks. With the available overhead and
  MC33926: 5.0 A Throttle Control H-Bridge, this could also be used for the
  fuel pump PWM project someone has been working on.
  C. Smith

 Paul, I was looking at some RX8 engines in my hanger this afternoon and the
 stock crank angle sensor looks just fine as is, and we know that it will
 function at 13,000 rpm so should be fine down at 7,000 continuous. The
 spacing to the triggerwheel looks excessive IMHO but some testing with the
 oscilliscope on a running engine at the stock spacing and at a few closer
 spacings might be interesting.


 The freescale board download shows 10 analog
 to digital converters which is really generous. Their mixture control seems
 to use an oxygen sensor so that would be the area to exchange for an
 algorithm of the mass air flow to fuel ratio. I really like the 90MM ford
 maf with the built in temperature and humidity correction on the sensor
 circuit board. The freescale board has air temperature sensor input and more
 importantly engine temperature so the code for a second air temperature
 correction would need a revision.

 Do you think the MAF sensor gives a more
 precise reading than the manifold absolute pressure, and particularly when
 higher turbocharging pressure would require a larger range of sensitivity?


 It would seem that the charge temperature and manifold pressure.
 sensors would need to be at the same place and that vaporizing fuel lowering
 the temperature would make accurate readings difficult at different fuel
 flow rates. With the MAF sensor reading only air it appears to have the edge
 on accuracy.

 george grimes

 Yes, The mass airflow sensor would probably be more accurate.

 Paul Lamar


Can a pitot tube in the intake stream replace the heated mass air flow sensor?


Matt-

Probably. I think you will also need the air temperature.

It will need to be a very sensitive pressure sensor as  100 MPH is only .18 PSI.

You will also need to relate it to ambient pressure.

Here is a data sheet.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.