Subject: [Slide throttle: Needed with carb?
From: Rotary Engine
Date: 11/12/2009, 8:58 AM
To: AAA Put this in the To box



 I'm fairly sure I'm going to eventually go with a simple mechanical carb
with manual
 leaning (as we discussed a while back).  If so, what's the likely penalty
 (HP/weight/fuel consumption) for using the built-in throttle on the carb
rather than
 going with the more efficient slide throttle for a NA 13b P-Port setup?
 Thanks

 Mark W.


 I don't know Mark but my guess is not much.  The big problem with a 13B
p-port and carb
 is idling stability. You need the throttle close to the rotor housing. With
an RX8 side
 exhaust it would be just as  stable as a side intake 13B.

 ---------------------------------------------------------------------

 Another problem you will have to deal with is stand off fuel vapor. With
any tunned
 system air flows both in and out of the carb. At around peak torque plus or
minus 1000
 RPM lots of fuel vapor is generated outside the carb as the air flowing out
of the carb
 also sucks fuel out of the venturi. You can see this in our Youtube video
Using a weber
 carb.

 http://www.youtube.com/watch?v=LkKw72dZ2yc
 http://www.youtube.com/watch?v=KQL45DYgIFw

 We checked for this with fuel injection on Marks Suspinski's engine and it
does not happen.

 You will have to deal with this fuel vapor with a sealed air box above the
carb to make
 sure all the fuel vapor is captured. I am not sure how much of this happens
if the air
 box is provided with ram air at cruising speed. I suspect the phenomena is
much reduced.
 Sorry but you will be on the cutting (bleeding?) edge.

 Here are some 3D's of a system using a Holley 500 CFM two barrel carb with
leaning block.

 Paul Lamar

 ***********************************************************
Paul,
 Thanks very much.  Yes, something will have to be done about the fuel vapor
"outflow".  I think the ram air might help hold things inside an air box at
cruise speeds, but on takeoff it wouldn't be much help.  Maybe (at cost of
some efficiency) go with a carb location closer to the engine and tuned
pipes before<< the carb?  I'm sure the change in intake diameter through the
carb will eliminate the chance to get a constructive standing wave from the
intake port to the bel mouth, but maybe a constructive wave from the carb to
the bell mouth could be set up with the right runner lengths.
  Or maybe intake length tuning is too much trouble for my simple
application.  I'll already have more HP than the plane is designed for, and
simplicity and weight are both important factors.  Maybe for me the best
option is an air box fed by ram air, convenient length runner to the carb,
convenient length runner to the engine.

Mark W.

There is limited room to put the carb closer to the rotor housings.
You could lose 50 HP in a p-port config and more in a side intake port
config.
Early 13B's with 4 barrel carbs were 145 HP.

What kind of aircraft are you building?

Paul Lamar


As I suggested a while back, a P-Port RX8 engine with tuned intake
runners leading to a plenum of proper volume onto which is mounted a
carburetor shouldn't have much in the way of a fuel standoff problem.
The reversion effects should be contained within the plenum I believe.
The plenum could extend across the top of the engine.  If using an
automotive carb, it could be mounted on the cold side of the engine,
near the firewall.  On a tractor install the inlet air could come from
the base of the windshield (cowl induction in car automotive terms),
or an ME109 style scoop could extend forward.  If using an aircraft
carb, it could be mounted low on the cold side of the engine near the
firewall with a single runner extended upward to the plenum.  Use
flexible hose to make connections between rigid sections of the system
(a la the O-470 intake system).

Another thing I've seen in some cars is two sets of throttles (in
series)..  One within the carb and one closer to the engine (in our
case, a slide throttle mounted on the housings).  The two throttles
are connected so that they are at the same relative flow.  That should
allow a P-Port 13B to idle well and allow running a carb with a tuned
intake length.  It's extra monkey motion getting the throttles synced
up, but it might be worth it to allow a 13b based engine to use a
cheap (Holley) carb.


Matt-


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.