I'm fairly sure I'm going to eventually go with a simple mechanical carb
with manual
leaning (as we discussed a while back). If so, what's the likely penalty
(HP/weight/fuel consumption) for using the built-in throttle on the carb
rather than
going with the more efficient slide throttle for a NA 13b P-Port setup?
Thanks
Mark W.
I don't know Mark but my guess is not much. The big problem with a 13B
p-port and carb
is idling stability. You need the throttle close to the rotor housing. With
an RX8 side
exhaust it would be just as stable as a side intake 13B.
---------------------------------------------------------------------
Another problem you will have to deal with is stand off fuel vapor. With
any tunned
system air flows both in and out of the carb. At around peak torque plus or
minus 1000
RPM lots of fuel vapor is generated outside the carb as the air flowing out
of the carb
also sucks fuel out of the venturi. You can see this in our Youtube video
Using a weber
carb.
http://www.youtube.com/watch?v=LkKw72dZ2yc
http://www.youtube.com/watch?v=KQL45DYgIFw
We checked for this with fuel injection on Marks Suspinski's engine and it
does not
happen.
You will have to deal with this fuel vapor with a sealed air box above the
carb to make
sure all the fuel vapor is captured. I am not sure how much of this happens
if the air
box is provided with ram air at cruising speed. I suspect the phenomena is
much reduced.
Sorry but you will be on the cutting (bleeding?) edge.
Here are some 3D's of a system using a Holley 500 CFM two barrel carb with
leaning block.
Paul Lamar
***********************************************************
Paul,
Thanks very much. Yes, something will have to be done about the fuel
vapor
"outflow". I think the ram air might help hold things inside an air box
at cruise
speeds, but on takeoff it wouldn't be much help. Maybe (at cost of some
efficiency) go
with a carb location closer to the engine and tuned pipes before<< the
carb? I'm sure
the change in intake diameter through the carb will eliminate the chance
to get a
constructive standing wave from the intake port to the bel mouth, but
maybe a
constructive wave from the carb to the bell mouth could be set up with the
right runner
lengths.
Or maybe intake length tuning is too much trouble for my simple
application. I'll
already have more HP than the plane is designed for, and simplicity and
weight are both
important factors. Maybe for me the best option is an air box fed by ram
air,
convenient length runner to the carb, convenient length runner to the
engine.
Mark W.
There is limited room to put the carb closer to the rotor housings.
You could lose 50 HP in a p-port config and more in a side intake port
config.
Early 13B's with 4 barrel carbs were 145 HP.
What kind of aircraft are you building?
Paul Lamar
------------------------------------------------------------
Paul,
It will be a Vision. (
http://pro-composites.com).
The designer wants 300 lbs max FWF and calls for an engine of 100-160HP,
I'd like to be
on the high side of that range--or slightly above it. Two examples with
O-320s have
flown.Would a 13B p-port with a 4 bbl need to have a properly tuned intake
in order to
make 160HP? Some of this might also depend on the exhaust configuration,
I'd like for
the plane to not be excessively noisy.
Mark W.
Well you have a lot of time to make a decision on the engine.
The cowling will be tight so pick a config that is low height.
A stock manifold will get you 150 HP. You might contact racing beat or
Mazdatrix and see
if they have a manifold for a Holley 4 barrel and then you could get 2
leaning blocks.
Is it a 4 port or six port 13B?
Paul Lamar
Paul,
Oh, yes, I've got a lot of time before I'm ready. I don't have an engine
yet (if I did, I would have done all I could to get it to you for the
present P-Port-a-thon you are running!). I was hoping a p-port drawing
through a 4 bbl carb, even with a non-tuned manifold, might make 160HP.
But, "hoping" isn't the same as "getting."
Mark W.
Well that changes a lot of things. Try to get an RX8 engine and p-port it.
There is a cost penalty for using a side port engine with a Holley 4 barrel.
Manifold and Holly 4 barrel carb would cost you close to $1000.
In a Vison there is no room under the cowl for an up and over manifold of
any kind as I recall.
Paul Lamar
How long would the intake runners need to be to get the peak
horsepower at around 5500 RPM? 27 inches? More? You can probably
use smaller runners which might be easier to fit in the cowl.
What I'm getting at is if you only need 160hp, get it by tuning
properly for a lower RPM instead of messing up the volumetric
efficiency with a crummy intake design. Will the engine get a bit
better fuel economy by turning slower?
Those cast manifolds look heavy.. Are they?
Matt-
Real long as we don't have any data on it. The diameter also changes the tuning.
The BSFC actually starts going back up at less than 6000 RPM. You save fuel by running
the engine at lower powers.
Those cast manifolds are heavy and so is the Holley 4 barrel.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.