Subject: We are going to flood the skies with p-ports.
From: Rotary Engine
Date: 11/12/2009, 11:37 AM
To: AAA Put this in the To box


  This is not all of them. There are four more.

  We have done a couple of junk rotor housing so far to tune the process.

  The biggest limit on how fast you can drill a 2 inch hole in a rotor
  housing is the
  rigidity of the mounting fixture and the power and rigidity of the
  mill. Compared to a
  Cincinnati or Kasuga a Bridgeport is a wimp. There is NO substitute
  for tons of cast
  iron and lots of HP :)

  http://www.youtube.com/watch?v=7odN-h7rsGQ

  We now have two angle plates bolted together with  four pieces of
  5/8th inch diameter
  threaded rod and eight 1/2 inch hold down T bolts on the Bridgeport
  mill. I wish my
  Kasuga were running.

  -----------------------------------------------------------------------

  One of the other things we tried was an experiment with the weld on a
  junk housing.
  We recessed the tube 1/32nd into the bore resulting in a much lower
  profile weld so you
  won't have to do much die grinding to clean up the transition. The
  weld bead  is almost
  flush with the rotor housing wear surface. It never ceases to amaze me
  how well these
  welded p-ports work. IMHO it is the only way to go.

  On the other hand you will need a special long tap so the tap handle
  will clear the SS
  tube. The tube protrudes about 1.5 inches at the top. This needs to be
  done to clamp the
  sealing blocks to the rotor housings. I recommend a Greenfield
  EM-AL-GUN-TAP 1/4-20
  Rutland Tool & Supply part number 7116 4207  Cost is $12.73. This tap
  is 3.15 inches
  over all length. Drill the top left tap hole about one inch deep. That
  is the only blind
  hole. The other three are through holes into  the water jacket.

  Take your time and don't screw this up as a repair with a helicoil set
  could be real
  difficult.

  We have done the hard part. It is up to you to do a bit of time
  consuming finishing
  work. I can't promise when we will ship as the blocks are in the NC
  shop for the O-ring
  groove. I think I will order the right O-rings for you and install
  them in the blocks.


  Here is another idea. Instead of using uncured red RTV silicone rubber
  one can buy cured
  RTV in films to use as a conformal gasket. Good to 500 F.

  http://www.mcmaster.com/#rubber-sheets/=4geun0


  Paul Lamar


  Paul,
  what filler rod is he using when he welds the housing?
  Thanks,
  Larry

I don't know.  I don't think it needs much. There is no load on them so weld strength is
not an issue. A good weld without porosity is more important for pin hole leak problems.

I'll ask him what he is using.

--------------------------------------------------------------------

Here is what the set up looks like.

Don't be fooled by the sealing blocks. One person sent us the rotor housing with the
sealing blocks already installed and teh cavity potted with JB Weld. We left them on
there as an experiment when we bored the housings. We will replace them with the new
sealing blocks with the O-ring in them.

The blocks are finished and waiting for me to pick up in the NC shop.

--------------------------------------------------------------------

We discovered a minor problem with the RX8 rotor housings. I am not sure they are all like this as there is a cosmetic flaw in the housing. Smooth the area as much as possible with a Dremel tool drum or disk sander. Then I suggest grinding the flaw out, use a conversion coating  and filling the area with JB Weld. Then cover the sealing block with saran wrap or wax paper and press it down on the JB weld to flatten it out. JB Weld or any epoxy for that matter will not stick to aluminum. You must convert the raw aluminum. You get the conversion kit in boat stores. This may apply to all types of rotor housings.

You don't want to glue down the block as you may need to change the O-ring some day.

Then use a silicon rubber film as a gasket on top of the JB Weld.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.