Subject: one rotor Questions for Lewis Bjork
From: Rotary Engine
Date: 11/23/2009, 9:15 AM
To: AAA Put this in the To box



 Lewis

 I have a Q200 with a Lycoming 0-235.

 Paul advised that a single rotor was the way to go on this airframe.

 The Ross re-drive the same as used on the two rotor?

 I have 2 two rotor engines and a 3.17 Ross myself, but think the package
 with exhaust/radiators and ancillaries would be too heavy, have you any
 weights?

 Can you post some pictures engine and airframe?

 How about a show and tell, as there seems quite a bit of interest already.

 Clive Clapham

 No weights yet. Probably at least as heavy as an O-200. Using the same
 Ross drive as the two rotor engines. I would prefer a drive with less
 reducton. 3.17:1 sets the prop just under 2000 rpm while the engine turns
 6000. The Q200 has limited prop length available (landing gear geometry).
 Even with a 68 inch prop--which is long enough to require great caution to
 avoid a prop strike-- in-flight adjustable pitch is required to take
 advantage of the power and speed range of the airframe. I have mounted a 2
 blad IVO magnum with electric pitch control. This is a good 15 pounds
 heavier than a fixed pitch propeller and is probably my single biggest
weight
 issue forward of the firewall.

 On the upside, if it all works well, the plane should not be very loud.

 The engine has been mounted with the plugs up--about the only way to fit
it
 in a Q200 cowling. It is 7 inches too long, however, and reqiured that I
 make a new cowling, anyway. The biggest problem was the starter motor
 protruding forward, just behind the spinner. I simply bought a 14 inch
 diameter spinner and moulded a new cowling to fit. Not yet finnished, but
I
 think it's coming along nicely.

 Using the exhaust system and muffler to augment airflow out of the cowling
 should improve cooling flow. Also cut into the fuselage a bit to channel
the
 exit flow and reduce cooling drag--see pictures. Have yet to configure the
 induction/filter plumbing and intake.


 Using an airconditioning condenser of 240 cubic inches for cooling. This
 sits in a moulded fiberglass plenum. Also a large oil cooler with its own
 dedicated intake.

 Some photos are included.

 Spoke with Tracy Crook some time ago and he suggested a simpler approach:
 Use a modern Renesis engine with the automatic transmission flange, no
gear
 reduction, and direct drive a prop at around 33-3500 rpm. Would make alot
of
 noise, but with careful plumbing could fall under 200 lbs installed,
develop
 100 hp or so, and the engine would never wear out. I may try it if the
 single rotor approach does not work out.

 Lewis

 You should replace that aluminum oil pipe with braided line before you fly
it
 as it has a habit of vibrating and cracking. The engine will seize in
short
 order as soon as it pumps its precious bodily fluid over board :)

 One would be very lucky indeed to get 100 HP out of an RX8 engine at 3500
RPM.

 Paul Lamar
                        
Thanks Paul,  I'll do that.


Lewis.


Lewis

Thanks for the pictures, looks good.

I take it that the main reason for the plugs up was distributor and
alternator?

Good idea to take not of Paul's advice on replacing the fixed pipes with
flexible, at least before flight.

I'd be interested in your weight and balance?  Mine weighed 580lbs in a
similar state of undress before paint and instruments; final weight ready to
fly 650lbs. CG was with in limits and did not alter very much.  So you could
do a bathroom scales w&b, before paint incase there are any surprises.

Keep us all posted, plenty of pics.

Clive



-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.