Subject: Mechanical/electric fuel injection sort of
From: Rotary Engine
Date: 11/27/2009, 9:23 AM
To: AAA Put this in the To box

 I had a talk with a Sprint car mechanic recently and mechanical fuel
 injection is widely used in 800 HP Sprint car engines. Kinsler is a major
 supplier of parts. What I am thinking of doing is use a pulse width
 controlled electric fuel pump instead of the engine driven Kinsler fuel
 pump.
 My friend tells me there is a thing called a "pill" that bypasses the fuel
 back to the tank. The size of the hole in the "pill" controls the max
 pressure the fuel rail sees.

 What happens with fixed orifice injectors is the fuel pressure goes up as
 the volume of fuel going through the injectors increases. Sprint car drivers
 are not allowed to change the "pill" while driving but a needle valve on the
 instrument panel could serve the same purpose. This is a super simple fuel
 injection system and super low cost as one needs a fuel pump in any event.
 The 555 circuit I have will work as is to control the pump speed based   on
 either manifold pressure sensor output  or mass air flow sensor output.

 I just checked an electric  pump I had to verify the housing of the pump was
 electrically isolated from the negative side of the motor connector. This is
 a long story  as the PWM circuit switches the low side of the load just like
 a fuel injector. One of those little details one must worry about.

 The first option is the cheapest as the sensors cost about $10 while the
 second can cost up to $100. The manifold pressure sensors are linear while
 the mass air flow sensors seem to put out a square law voltage with air
 flow.
 I am not sure about that statement as I have not extensively tested one yet.

 That I can do by sticking it out the window of a moving car and recording
 the voltage out as a function of car speed.

 The first configuration tested will be the pressure sensor as a low cost
 hand vacuum pump can be used to simulate the manifold pressure over a wide
 range.

 BTW I suggest everybody install Quick Basic on their windows computer as I
 will be using it a lot in the future to calculate various and assorted
 things as it works well for doing this. Easy to learn but if your ISP will
 not pass a zip file, that I can send you, then you will have to send me $5
 for a DVD.
 Included in these attachments is a picture of a QB program to calculate the
 fuel flow through an orifice. You can just type it in by looking at the
 picture.

 A spread sheet will also work but I am not as quick using them as I am QB.

 Paul Lamar

 Paul, in the mid "80s I was working for an infra-red instrumentation house.
 A great deal of our products were purely analog, (even the first fire
 control "computers" were all analog systems, like the Mk II GFCS in
 Missourri class battle ships). I recall, just after a couple of our
 engineers left to form their own company, they came by with a schematic they
 wanted analyzed (as they were degreed engineers, and I was just a tech, I
 still wonder why they were asking me). What I figured out was that it was an
 analog computer, with electrically variable terms, not just a scaling
 amplifier. It took a lot of digging through application notes and reference
 books, but I still believe that just about anything can be done with analog,
 given a need and motivation. Fire control is not a linear equation.
 C. Smith


Long before digital processors, the Bosch Fuel Injection systems where analog based computers.

D-Jectronic, and early series L-jetronic.  Pretty robust little analog computers.  The inputs are nicely protected from ESD, and had decent
filtering so RFI noise didn't upset the circuits. The  boards had resistors mounted on stand offs. As test equipment checked
everything, the tester would 'calibrate' the resistors to be added, selected from a bin, and usually the ladies would pick up the resistor
(bin was lighted with a little LED for the correct on), and solder it down in place.

The biggest draw back was a faulty sensor. Usually wiring could be shorted or open.  With a micro-controller (uC) this became easier to test for out of  bound conditions.  With a range of 0 to 5V, you would set up the normal operating range for 0.5V to 4.5V.   Outside of that range you knew it was a faulty sensor, shorted, or open wire.

I'd check with the production folks on customer returns, and usually we found over 97% were fully functional, and should not have been returned. With the uC you could set a code for the technician to check one of the sensors.  Yes, you can do discrete comparators for analog inputs, too. If the sensor out of bounds, have a LED light up.

Tom W

I had a VW square back with EFI. Gave no trouble at all.

The 555 was invented in 1970 by Hans R. Camenzind who was an electronics engineer from Switzerland, the 555 timer was first produced by Signetics in 1971.

http://en.wikipedia.org/wiki/Fuel_injection

"The first commercial electronic fuel injection (EFI) system was Electrojector, developed by the Bendix Corporation and was to be offered by American Motors (AMC) in 1957.Chrysler offered Electrojector on the 1958 Chrysler 300D, Dodge D500, Plymouth Fury and DeSoto Adventurer, arguably the first series-production cars equipped with an EFI system. The early electronic components were not equal to the rigors of underhood service, however, and were too slow to keep up with the demands of "on the fly" engine control. Most of the 35 vehicles originally so equipped were field-retrofitted with 4-barrel carburetors. The Electrojector patents were subsequently sold to Bosch."

"Bosch developed an electronic fuel injection system, called D-Jetronic (D for Druck, German for "pressure"), which was first used on the VW 1600TL in 1967. This was a speed/density system, using engine speed and intake manifold air density to calculate "air mass" flow rate and thus fuel requirements. The system used all analog, discrete electronics, and an electro-mechanical pressure sensor. The sensor was susceptible to vibration and dirt. This system was adopted by VW, Mercedes-Benz, Porsche, Citroën, Saab, and Volvo. Lucas licensed the system for production with Jaguar."

Here is the patent on the CD ignition system.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.