Subject: Turbo compound spin muffler / cooling/ heat loss
From: Rotary Engine
Date: 11/30/2009, 5:40 PM
To: AAA Put this in the To box


 Paul,

 I often wondered why I like those disc impeller pumps so
 much.  Then it
 dawned on me.  Tesla turbine.

 Not happy with how my ideal TC engine was physically
 forming up I
 decided
 to give the Tesla turbine another look.  I spent a
 sleepless night
 designing a true spin muffler that would be driven by the
 exhaust of the
 rotary engine.  Size restrictions dictate a six inch
 diameter turbine
 section and perhaps one for each rotor housing.  A
 common shaft is do
 able and puts the bearings outside the case. Most of the
 components
 should be made from Inconel or even titanium. Stainless 316
 is good
 enough for the testing.  Laser cut plates
 absolutely.  At least for the
 13B the Tesla turbines exhaust could exit near the
 intermediate housing
 and  feed a small T4 hybrid turbocharger.  Tesla
 turbines are tune-able
 for the desired rpm output by removing or adding discs.

 Most of Tesla turbines motors out there have been running
 on high
 pressure air or steam simply because it is available but
 hot gases are
 also possible depending on the ratio of inlet to outlet
 port size.
 Turbine efficiencies are quote at from 40 to
 95%.   The higher figure is
 nonsense IMHO.  Centrifugal turbine are in their mid
 50s at peak so I
 suspect the lower quote is closer to ball park.  Axial
 turbines are a
 bit better but either of these high rpms or large diameter
 turbine are a
 logistic nightmare.  I have believe a T4 radial
 turbine is not going to
 be able to recover much more than 30hp. at speeds low
 enough for a
 traction drive to handle it. The mounting and connection
 considerations
 are also daunting.  This started to add up to
 unacceptable weights.

 I had orginally designed a spin muffler around a central
 pipe punched
 with bypass exhaust holes and a  with the
 planned  turbine to be mounted
 outside on the muffler case. Making the spin muffler
 literally spin
 saves space perhaps development time.  It it saves me
 from having to use
 a supercharger so much the better.

   I can see a few points that may increase the Tesla
 turbine efficiency.
 New spacing methods to lower windage,  texturing the
 discs, and
 eliminating skin drag loss on the outer end housings.
 If nothing else
 it would make a heck of  a quiet
 muffler.   Injecting air into the
 exhaust nozzles would help contribute to a complete burn
 and increase
 inlet pressure.

 Putting the turbocharger on the outlet of the Tesla's spin
 muffler would
 subject it  to lower temperatures.  Will it
 work?  Who knows but at
 least this is something I can build and test.

 Anybody else have some thoughts on design feel free to
 chirp in.
 Depending how it mounted it could feed the power to the
 accessory side
 or the PSRU side of the engine with the obvious differences
 in required
 shaft lengths.

 Now I am thinking to make a prototype with the housing made
 of a six
 inch
 ID Inconel pipe.  Discs will be SUS316L.  2.0 mm
 thick. Spacing at least
 2.0 mm. Numerous discs. Both exhaust pipe rectangular
 and tangentially
 wrapping at least 60 degrees around the outer muffler
 housing.


 Doug in Japan


 That is interesting.  I have been thinking along the
 same lines
 recently.  I'm building a 14" disc prototype.  I
 guess my input would be
 to consider water injection as well.  I've seen posted
 the thought that
 spacers on the periphery don't degrade efficiency.  If
 you used wafer
 thin ferrite magnets you might be able to use the turbine
 as your
 alternator.  I'd be very interested in seeing any
 formulae you may have
 found in your research to calculate efficiencies, etc.
  Decker, Michael


If you'r suggesting the magnets are also exposed to the exaust stream,
it's a
non starter. The magnets subjected to that high a temp. would surely
reach the
Curie pt where the magnetic properties go to zero.
Robert


100hp=64,000,000 calories/hour 800 degrees C to 260 degrees C = 260 lb.
of water/hour to obtain that temp.

Just thinking out loud...:)

Decker, Michael


Good way of looking at it Michael

Here it is in English. :)
Inlet temperature = 180 F
Outlet temperature = 190 F
Coolant flow = 100 GPM
Specific heat of coolant = 1.0 = SpHt
1 HP = 5.2769885 x GPM x 1 x per Fahrenheit drop
((Outlet-Inlet temp. in F) GPM x SpHt) / 5.2769885 = HP cooling loss.
((190-180) x 100 x 1.0) / 5.2769885 = 189.5 HP cooling loss.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.