Subject: Cooling your oil in general
From: Rotary Engine
Date: 12/20/2009, 7:51 PM
To: AAA Put this in the To box


 Modine has a great step by step out on how to select an oil cooler. It is
8
 meg so I can't email it but I did just upload it to the web site. I
suggest
 everybody download the pdf.

 http://www.rotaryeng.net/Modine-calc.pdf

 This is a real Christmas present for us as it takes some of the guess work
 out of choosing an oil cooler that works.

 There is a some information you will need to know about the rotary.
 You will need to know the HP you are trying to cool.
 For that you need to look at this heat balance chart.

 I have modified the chart to make it easy for a 200 HP side port 2 rotor
 but
 if you have a  p-port two rotor you will have to multiply the oil cooling
 HP
 number by 1.25. That means a 250 HP p-port engine running at best power
 mixture of 12.5 to one is rejecting 63 HP or 25% of the net HP out of the
 engine to the oil.
 You then plug this number into the Modine equations to figure out the
 number
 of BTU's per minute you will be rejecting.

 The next thing you will need to know is the GPM of the oil pump through
the
 system. The stock number I think for the 2nd gen engine is 1.3 GPM at 1000
 RPM.
 At 7000 RPM it would be seven times that or 9.1 GPM. That number is
 somewhat
 dependent on the oil system plumbing and the size of the cooler. A larger
 cooler with more tubes is going to allow the pump to flow a bit more oil.
 Also right angles in the oil gallery of the engine also reduces the flow.
 More about that later. Lets say it is 10 GPM for a 2nd gen oil pump.

 I think the 3rd gen pump is larger and the 3 rotor may be larger yet but I
 have no hard data yet. You will probably need to make some assumptions
 about
 that.
 Perhaps someone on here has measured the 3rd gen pump oil flow. I think
 Mistral did that and I may be able to find it.

 Follow the first 3 steps in the pdf.

 Note the lower the Viscosity of oil the better it cools. Use Idemitsu
 rotary
 engine oil. I used to use Mobile 1 SAE 15 weight for 15 years but I am now
 using Idemitsu. I think Mazdatrix sells it.

 In Step 4 you enter the Modine chart called Curve 1 and you pick a LAB
130.
 With a LAB 130 you will get a very low oil pressure drop across the cooler
 amounting to only a few psi. A Lab 130 core is about 22 by 22 by about 2
 inches thick. A smaller core will probably work as the airflow will be
 higher than what is called out in this PDF.

 Continue following the steps in the PDF to calculate the pressure drop.

 What is missing here is the airflow data.

 Paul Lamar

 When trying to open that link I get "file does not begin with %PDF- " and
 it
 will not open.  Im using IE8.
 C. Smith

 I just tried it with Firefox and it left clicked and right clicked.
 Anybody else having trouble?
 What OS are you using now?


 Paul Lamar


Paul,

I had the same result as C. Smith had.  I'm using IE.

Mark S.

What OS are you using?
http://www.rotaryeng.net/CW-aluminum-rotor-patent.pdf
Does this link download?

Log on to the web site and scrol down to Tech Topics and then click on How
to Cool. Try getting it that way.

Paul Lamar

Paul,

The link above worked, but not the "How to cool your oil using Modine
coolers" link as listed on your web site.  I'm running Windows XP.

Mark S.

It appears to be an Adobe reader problem. See if yoiu can down load and save it.
My reader has no problem with it.
Document Viewer 2.26.1
Using poppler 0.10.5 (cairo)

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.