So we want light weight side housings but also a tough wear surface,
right? Can we band saw all but about 1/4" of the factory iron side
housings away, and then use most of the Racing Beat aluminum housing
mated to it? What kind of gasket or seal would be required between
the iron and aluminum?
Happy New Year!
Matt-
I have been doing that for my single rotor work since about 10years ago.
The
prove of principle engine is still running strong with this arrangement.
The problem area I encountered is around the stationary gear area whrere
the
CI and AL need to be connected (first picture). It was only possible with
a
lot of JB Weld, in a way I would not want to have in a flying engine.
The flying engine side housing has a CI running surface insert(second
picture).
I do not have a design for the center housing nor for a power-take-off
side
housing.
Happy and prosperous New Year.
Richard Sohn
N2071U
Cool.. I knew it was a good idea. :)
Stationary gears. Yeah. I hadn't thought about those. Would have to
work around them. My first thought is to leave enough CI to mount the
gears and mill away a matching amount of Aluminum for clearance.
Nothing is ever simple.
Matt-
The devil is in the detail! And it is a big devil.
Richard Sohn
N2071U
Milo, The air cooled rotarys that have been built are all of low horsepower
due to the heat load of an engine that is continually firing. The Mazda
makes 100HP per rotor with P-port intake and a lot of heat. The heat is in
a
confined space on a very compact engine. The stock rotor housings don't
lend
themselves to air cooling due to the construction. There is an inner wall,
an outer wall, and webbing in between with coolant between the webbing.
Manufacturing rotor housings from scratch would be technically difficult to
machine due to the shape and accuracy needed, and then it must be lapped to
a relatively high finish. There have been companies like Rotamax that have
used "charge cooling" which circulates the intake fuel/air charge through
the engine using the latent heat of evaporation for much of the cooling,
and
liquid cooling for the rest. IMHO they will always be low in HP due to the
long complicated path the intake charge must follow thru the engine, and
the
fact that the charge is less dense if it is hotter. They are following the
OMC design. The air cooled rotaries are mostly for RC models and Karts.
There have been diesel truck engines with the piston tops made of ceramic
materials and a few engines with ceramic cylinder liners. It may be
possible
to build a rotary out of this technology with ceramic rotors with a steel
bearing/gear sleeve carrier in the center. Ceramic facings on magnesium
side
housings as long as threaded holes are avoided might be possible.In short
if
you can greatly reduce the heat soak into the parts you might get to a
heat
load that could be aircooled. The air cooled engines on motorcycles and
aircraft engines all have a higher surface temperature on the cylinder head
and upper cylinder wall than the rotary engines. There are rubber "O" rings
on the sides of the rotor which don't tolerate these higher temperatures.
There are "O" rings like the teflon encapsulated types with assorted
(expensive) core materials for up to 660 degrees
If you want to draw up one of these engines the dimensions needed
for the rotor housings and all the math formulas using eccentricity, major
diameter etc are in the two printings of a book by the Mazda engineer who
is
the definitive expert on these engines. You can download these for free
on the rotaryeng website and the "Craigs rotary page" website which has
most
of the history of rotarys . The dimensions of the Mazda tension bolts and
bell housing bolt locationa have been posted on this news letter about
July
this year.
You will find formulas, examples and sizing of everything about
the cooling in a book by Paul Lamar available on this web site. The address
for this was on the newsletter a few days ago.And finally take apart a
Mazda
engine and take a good look at the parts. A 54MM socket from northern
hudraulics ($10.99) is the only half way special tool needed. Just take out
all the fasteners and unstack the parts. The seal and flat springs behind
them in the rotors need tracked so they can be replaced where they came
from
during reassembly. There are videos (mine is by Bruce Terentine) available
thru Tracy Crook and another from Atkins rotary engines.
george grimes
Jeff, Good idea on the placement of the seam between the "O" rings. Looks
to be a center housing for a 3 rotor with RX7 rotor housings. If it is,
that's REALLY LIGHT !!! for that type of housing, and may be the first one
done in aluminum.
george grimes
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.