Subject: Sticking apex seals and rusted bolted.
From: Rotary Engine
Date: 1/12/2010, 8:03 AM
To: AAA Put this in the To box

snips............

To remove the difficult brass oil injectors you might try a 50/50
ATF-acetone mix. Wish I had known this many broken bolts ago.

http://forums.matronics.com/viewtopic.php?p=250660&sid=eee793f63491388f4697042c7bfda603



I forgot to mention that new oil inlets such as #2 (in particular) in
the engine pictures above have very little meat on Rx7 13B's. Plenty on
12A's. Haven't done the mod on RX8s. RX7 13B's required a bottoming
tap to get enough usable threads.

Cheers
Cary

-----------------------------------------------------------------

What do you think of using that 50/50 acetone ATF mixture on
stuck apex seals?

snips...

BTW Cary your PC clock is off. If the battery is dead you can
set the clock from time to time in Windows I think.

Paul Lamar

Regarding the ATF "trick" to decarbonize rotors and unstick seals. I
have heard/read of revived 0 compression and seized engines..
IIRC, a few people have also said they had oil/coolant failures shortly
after decarbonizing engines with good compression.

I haven't heard of anyone actually putting orings in a solution to
measure the effects against a control. (sorta scientific like)
I don't think I would try it on a decently running engine until the
effects are known.
I would just rev it up regularly...6k a day keeps the rebuild away...
If you already have a seized engine or 0 compression faces and don't
want to rebuild, I would try some other light oils first.

Old PC clock drift corrected.

Cheers
Cary

Traditionally we use ATF alone for unsticking apex seals.
If you use Teflon O-rings I don't think acetone effects them.

Your clock is now one day ahead :)

Paul Lamar

If the engine runs you could try the "water injection" (actually water
induction) method. I used this successfully to unstick piston rings in a
car that was burning oil. You simply rev and hold the engine to about 3000
RPM (maybe more for a rotary?) and introduce water into a vacuum line.
There are a few YouTube videos showing different ways of doing this. I used
the tip from a bottle of sewing machine oil as a restrictor in the end of
the line so I could let it draw continuously rather than dunking the end in
and out. I wired a heavy nut onto the end of the line so it would stay at
the bottom of the jug. I also used a zip tie to hold the throttle open
(with side cutters handy) so it was a hands off process. It took about 10
minutes to go through a gallon of water IIRC. The size of my restrictor was
very conservative but it's best to err on the side of caution when doing
something like this.

Everett


When the apex seals stick and the rotary engine does not start it is
usually the result of letting the engine sit around for a couple of months
after mineral type engine oils have been used. Some say cheap gas but
that I doubt. The apex seals run 500 F and mineral oil breaks down
to tar and gunk around 250 F while synthetics will hold up and two
cycle oil burns cleanly.

Perhaps 100 LL aviation fuel is the cause which has a lot of lead in
it. When that happens the engine usually will not start so the water
trick will not work of course. What has worked in most cases is filling
the chambers with Automatic Transmission Fluid with the spark plugs out
and turn it over several times. Then let it sit for 24 hours. Then it
usually starts.

If that does not work.
The other thing that can be done on the exhaust p-port engines is remove
the exhaust manifold and use a soft wood dowel or just your finger and move
the seals in and out one at a time... three per rotor to see which are stuck.

Then squirt a little WD 40 on it and see if you can get it to move freely.

The stock RX8 engine is another matter. Sometimes they won't start because
they get flooded. This happened to me on my 2004 RX8 which was one of the
first sold in the LA area. It took the dealer in Santa Monica a week to
figure it out and get it started again.

The raw fuel accumulates in the engine and the mixture is
too rich to fire. In that case you need to set each rotor to about 180 degrees
before top dead center, insert a small dia. plastic tube long enough to
get to the bottom of the engine in the lower spark plug hole and suck the
raw fuel out of there.

Sometimes you can get enough out by merely removing
the sparks plugs, squirting some ATM in there to act as lubricant and
turn the engine over with the battery for five or ten minutes. Make
sure the spark plug wires cannot spark as there may be a ignitable mixture
exiting the spark plugs holes.

Along the way Mazda reflashed the computer
to reduce this tendency. I don't know what Mazda Corp. is telling the dealer
mechanics how to deal with this now. My RX8 can now sit for a couple of
months and start right up if the battery was disconnected when I turned
it off. There is some drain in the system somewhere that runs down
the battery otherwise.

All this assumes the engine is mounted in a car or airplane and you cannot
simply rotate the engine 90 degrees with the spark plug holes down.

A P-port RX8 engine on the other hand is a different situation. You now
have good access to the apex seals through the intake port. Enough excess fuel
is likely to find it's own way out through these ports if the fuel injection
or carburetor is disabled.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word UTUBPLEASE
Copyright 1998-2009 All world wide rights reserved.