I got all my autocad drawings redrawen pretty much from scratch
into Rhino over the last three weeks. Basically the parts are a flat plate
with an external shape for the part, from which small solids are
subtracted
for water manifolds, lightening, porting of intake and exhaust,stationary
gear mounting, "O" ring lands and bolt holes.

  I have the pieces located within the plate part but am having trouble
subtracting them from the main plate using the "solids difference"
command.
Some subtract as expected, however about half of them return an error
message "boolian difference failed"

   I did a test run with the pieces as polysurfaces and had similar
problems. I have since converted them to solids with the "create solid"
command which appeared to work 100% of the time. I have eleven various
parts for foundary patterns and another eleven pieces for finished parts.
The engine requires six components, the rest are for differing motor
mounts,
water pumps, and a connector bellhousing to connect two engines end to
end.

   I also have difficulty with the "solids union" command which
returns "solids union failed"with the larger parts such as the sidewall
of
the bellhousing and the flange. Since some sections will subtract from
these
larger pieces and some similarly shaped sections will not, it appears that
the larger parts may not be the problem. All the parts have a 3 degree
taper
on the edges for use as foundary patterns.

   The various pieces were constructed with a bottom surface a side
wall and a top surface connected with the join command. The "cap planer
holes" command doesn't seem to work on complex shapes, just circles and
rectangles. The "surface from planer curves" command does work indicating
the curves (outlines) are indeed in the same plane.

 Any help anyone can offer would be greatly appreciated particularly with
the boolian commands. Also something which would indicate what error
caused
the error messages would be helpful. The manual shows how to apply the
commands but lists very little help on what to do when they fail to work.
Virtually the same documentation problems as Autocad.

george grimes

I want to see some renderings George :)

Paul Lamar

Paul, I would sure like to get your input on this engine and will send the
JPG output just as soon as I can figure out why the difference command
isn't
working. I did a JPG of another part and know how to save a render to that
format. Without the parts subtracted out all that would render is the
external shape sort of like something with a Christmas cookie cutter shaped
like a side housing.
   Yesterday my new desktop quit, something to do with windows system
check deciding to shut everything down. I did the clean all the cable
connections and t ran another few minutes. Now all I have is the BIOS
screen. I don't have a lot of spares for this newer stuff so I will send it
off -again-for the third time.
  If it stops raining I can get the electric service connected to the
hanger which is pretty much wired up except for the larger machine tools.I
should be getting the large format printer operating, but I am just about
tired of computer problems and have no reason to expect that plugging it
into the wall will get me airframe drawings in full scale.

george grimes

The difference command is very picky. You want to make sure both
objects are truly solid. Choose "solid" and scroll down to "cap planer
holes". That usually does the trick. Practice with simple shapes
such as two blocks of different size. For complex shapes
choose: analyzemass propertiesvolume and it will tell you where
you are going wrong.


Go to: http://www.frys.com/
choose: electronic componentscomputer componentsmother boardsintel
view all Intel boards. Scroll down to Item # 6033738

This is a brand new ITX mother board that will fit in any old case.
That INCLUDES the Atom processor for $80. << Some of the memory you now
have may fit. If you buy a mother board, Fry's will sell you
MS Xp for about half off. Around $100. You may need a SATA drive
for about 500 gig for about another $100. Most old keyboards will work
as well as VGA monitors you now have.

They also have a complete Acer system using the Atom, a 160 G drive
screen, 1 Gb memory, XP and keyboard for $200.

This is a lot of bang for the buck in computers.

Paul Lamar



Paul, The computer is already all new parts. Two 500GB western digital SATA
drives and one maxtor 330 Gb One drive for Linux and the other 500 Gb for XP
which I got for $102. I can put in a modum and microsoft will repair the XP
over the internet if I use the same mainboard it is regestered to. I had to
do that on the last crash. My ram is 2Gb Hitacchi and the moniter is a 19"
1600 by 1400 resolution. I tossed the $300 video card when it burnt up and
put in an older diamond viper which has been working fine for the 90 hours
since the last crash. The first setup ran about 11 hours.. That failure was
the power supply that came with the case and I put in a 550 watt high end
type with the extruded aluminum case.If the hard drive is crapped out My
rhino licence is a one install (annual) student version. If it's that then I
will probably not ante up again but just wait for the Rhino 5 which is due
out this year.

 While I am stuck I will research the analize mass pr
operties volume
command options and see how to use it. I have used the cap planer holes on
simple objects successfully, however these objects are much to complex for
it to work. I have tried redrawing a few using only arc segments and
increasing the minimum radius arcs to something larger. Still no joy. I
tried a trick I use in Autocad when something wont extrude on a tapered
solid. I use "curve offset" with an offset of .002 and just continue
offsetting the curve until it fails to offset giving a return of "curve
offset to two open curves" rather than "curve offset to one closed curve"

Sometimes I can offset .250 and come back .232 to where I actually wanted to
go and it works. If I offset this curve back to the original size it is
exactly the same so I hadn't forced a shape change on the curve. I am
familiar with the direction vector concept, just not why I should have to
deal with it as the default operation of the software. If a solid is
constructed from surfaces either the top or bottom normal has to be
"flipped" before joining the surfaces. This is not really a problem just
different. The supurb loft command in Rhino makes up for any small
annoyances. And the accuracy and speed get a high rating as well.

george grimes

And it is still crashing? Thank God I use Linux for email :)

If you are dual booting that could be the problem.
I would not run two different O.S.'s on the same computer
as there are all sorts of hardware registers that may get
set up differently despite what some of the Linux advocates
say.

Learn to use "loft" as an option to "cap" complex shapes.

Rhino is very picky some times on "difference" and "unions" on
complex solids. Sometimes I need to "explode" them into
a bunch of surfaces and "join" the surfaces one at a time.

This also happens sometimes when you do a lot of editing. When that
happens you should have a good idea of what the part is supposed
to look like so start over without all the patches.

One of the rules to keep things well organized is:
make sure "snap" is always on. If necessary set snap
to .001.

I have been using it for close to ten years and I am still
learning tricks from time to time.

It is one powerful tool however. I am still using 3.

Paul Lamar