4.5 hours to go and the number 70 RX8 is in the GT lead
and top 10 overall.
It has a been a truly epic battle.
The number 69 car may have broken a tension bolt.
Paul Lamar
I'm advised it was not a tension bolt on 69. There was a coolant leak that caused the DNF.
Dean Case
MAZDASPEED@MazdaUSA.com
(310) 318-4582
Thanks Dean. I saw white smoke out of the tail pipe which usually
means an internal coolant leak. We had a tension bolt fail in
an aircraft application and that is what happened.
The number 70 RX8 is now two laps ahead and up to 8th overall.
If those DP cars keep dropping out the RX8 may win the whole thing
with two hours to go.
They had a nice interview with John Doonan which I recorded and may
up load to youtube with John's permission.
Paul Lamar
Hi Paul
Is fuel burn data available for comparison between the recips
Vs rotarys within the same class for the race.
Would be interesting.
Steve Izett
Perth Western Australia
Building Renesis powered Glasair Super IIRG
-------------------------------------------------
BTW the RX8 won the GT class and eighth overall.
Fuel burn is higher for the rotary by about 10%. They adjust the tank size
on the race cars so refueling intervals are about the same. Just about
everything else is adjusted as well. Minimum allowed weight is adjusted.
Maximum allowed 8500 RPM of the rotaries is 500 RPM below the production
street car RX8's 9000 RPM . This is done so a wide range of sports cars can be
run in the same race. For example a Corvette would easily beat a 2 rotor
RX8 in a sprint road race so the RX8 are allowed to run the 3 rotor which
it was never sold with.
Where the rotaries shine is on engine reliability
and that normally causes the rotaries to win the endurance races such as
the Daytona 24 hour race and Le Mans. The first 1/4 of this GT race was
dominated by V8 powered cars such as the Camaro and the BMW. The next
half of the race was dominated by six cylinder Porsche's. Only in the
last 1/4 of the race did the RX8's move up in the standings.
Reliability is nearly
impossible to regulate by the race organizers so rotary engines are
frequently handicapped to the point of extinction. Rotaries dominated
endurance racing in the 1980's and early 90's until they were excessively
penalized by increases in required minimum car weight making them
uncompetitive performance wise or banned outright.
Another fact about the rotary used in the RX8's is the engine is basically
the same as it was in the stock 1974 RX4. No fundamental changes
have been made. It is exactly the same displacement per rotor and
the materials are basically the same. Cast iron end housings and rotors.
Die cast aluminum rotor housings with cast in steel liners. The more or
less stock 3 rotor engines used in the racing RX8's have been out of
production for twenty years.
On the other hand the piston engines it races against are
fundamentally different in detail design and materials than the engines
currently sold to the public being specifically designed for racing
and costing about $100,000 or more each. The connecting rods are titanium
for only one example. Despite this as many as four or five piston engines
catastrophically failed during the race in the hand grenade mode.
When and if light weight aluminum or beryllium/aluminum alloy rotors
are developed the max rotary engine RPM will increase from about 11,000 RPM
to about as much as 20,000 RPM with a proportional increase in HP per cubic
inch and HP per pound. One could be looking at a 110 pound, bare block,
two cubic foot (24" X 12" X 12"), mostly aluminum rotary engine putting
out 500 HP at 15,000 RPM with excellent reliability and durability.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.