BTW how many people on here can weld steel?
Paul Lamar
I have been known to fuse metal together...
Not certified or anything. I use mostly TIG.
Chris Cosman
Are you willing to mnake mounts for people?
Paul Lamar
In my tons of spare time.... sure.
It would need to be a for profit operation as I'm currently unemployed
and going to school full time; time to finish up that M.E. degree...
Do you mean, make them from scratch? Weld together a pre-fab tube kit?
What exactly?
Chris
Yes for profit.
Make them from scratch. I'll mass produce and supply firewall and
rubber cup holders.
Paul Lamar
Sounds doable. Count me in.
Are these the motor mounts that you've designed in Rhino?
What was Jerry Hey charging?
Chris Cosman
Yes on the Rhino designs. I don't really know what Jerry was charging.
Paul Lamar
---------------------------------------------------------------------
Chris Cosman, I used to build custom Harley Davidson show bikes for 7 years
as a hobby. My frame/chassis jig had a 68 shovelhead engine mounted off the
surface plate to fit everything clear of, and a slotted plate for rear axle
and stearing head position and angle. You can work much faster when you are
sure everything is OK. I had a spare chrysler engine to set up some prostock
drag race chassis also a real good deal. Surely someone can donate you some
run out side housings, rotor housings and an accessory cover. I got some
junk irons from Bruce Terrentine at the WWW airport just south of Raleigh NC
a few years ago, or possibly someone on the newsletter has an RX7 suitable
for a jig.
I would mount it off the bolt holes on the sides that mounted it in the car,
down to a plate with the center of the E-shaft as a punch mark. A jack bolt
at each corner would be used to set down or side thrust angles by tilting
the plate. The mounting holes attached to the engine would be soltted 2" for
different firewall distances. and the uprights would be two overlapping 3X3
angle irons with holes drilled on 1"
centers also for adjustment.
The stand in engine could be just end housings separated by threaded rods
to go from 2 rotor to three rotor but an engine core would permit the
muffler etc to be in place to build around. This arrangement would also
facilitate some optional brackets such as the side mount radiator mounts
In addition to the plywood firewall that the engine is sitting on, A
second plywood of the cowl cross section could be bolted to the front of
Jeff's mounting plate to make sure no tubing falls outside the cowling. The
builder could supply a cardboard template fit to his cowl.
Experiance has shown tha cutting the longest pieces first and fitting
each tube as you go saves material. Any tube with more than 1/16"
gap can be recycled to a shorter part. "Not tellin ya yer business" as the
say around here, but when u is old as dirt bin der dun dat.
george grimes
---------------------------------------------------------------
We have been there and done that George on your motor mount scheme and it
does not work well in an aircraft. Probably tens of thousands of messages
have been written on this subject over a 11 year period.
First: every Mazda rotary engine generation motor mount is different with
the mount starting on the 12A front cover and moving backwards in generation
after generation. It limits what you can do with the oil pan as the center
mount needs a depression in the oil pan. The current oil pan on the RX8 is
inadequate for air craft use. The third gen engines have the mount on the
back (car) housing. This relieves the block of the torsional loads and puts
the mount near the CG of engine gear box combination.
In almost every case it makes the exhaust manifold or turbo charger a
nightmare to fit in and remove in service. Not to mention the high heat the
rubber bushings are subjected to. That is why we have moved the MM tubes out
and away from the engine with the motor plate.
The current motor plate mount works with all generations as the engine,
gear box, prop and starter combo moves the CG near the rear (car) housing.
The motor plate does double duty and saves a lot of weight. It also puts the
500 to 600 ft. pound (avg) prop torque directly into the rubber bushings
where it must go sooner or later.
I want to standardize as much as possible to keep the cost within reason. It
has taken us 11 years to evolve this mount and I am not about to go
backwards. Probably a 100 mounts have already been built with many flying.
Mostly with the Schertz beam which is a variation but the same idea.
Reread :
http://www.rotaryeng.net/mm-instruct.html
Paul Lamar
Those pictures sure look like a worst case scenario.
What aircraft was that?
That's stuffing $10 worth into a $2 bag. ;-)
How well did that cooling configuration work out?
C. Smith
That is a KIS Cruiser that I own. Bill Schertz is flying a KIS
cruiser with a different cooling system. The turbo is a stock 1991 RX7
Turbo II similar to what Dave Leonard is flying. Here are some
pictures of Dave's airplane. His cooling system is similar to my KIS
Cruiser cooling system. IMHO the cooling system is not working
as well as it should because the back side of the rad is blocked.
Currently we have evolved to putting the main
rad on the other cool side of the engine mounted vertically.
You can see why we had to move the rubber bushings and motor mount tubes
outboard away from the turbo or muffler.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.