Subject: Dave Garber's bell 47 PSRU.
From: Rotary Engine
Date: 2/7/2010, 4:29 PM
To: AAA Put this in the To box


 Paul,

 On your website in the PSRU section you have a picture of Dave Garber's
 engine mount
 plate and the sun gear drive plate attached to a object that is obviously
 bolted to the
 counter weight.

 The object in question is a plate with some sort of cup in the center.  I
 forgot to ask
 Dave what that was.    I would guess it was for a bearing. Do you know?

 He didn't use any type of torque absorber on the his turbocharged 12A.
Did
 you notice any
 undue vibrations when you ran it at Sun and Fun?

 Doug in Japan

 We never let it idle below 2000 RPM.

 I think you are talking about these pictures.
 The big flaw in Dave's design was not enough spread in the
 prop shaft bearings. Those big props would have one heck
 of a gyro bending load on the prop shaft. All he had in
 there were two closely spaced giant ball bearings.

 From the looks of it all the bending load was transferred to
 the rear main bearing of the 12A. I would make a 3D of the
 whole thing as you have the parts so you have the dimensions.

 Paul Lamar


 Paul;
       20years ago I was building a PSRU out of the top 1/2 of a Bell 47
 gear box. The project got lost during a messy divorce.
 Does Dave Gaeber live in Florida?. I used to know someone in Florida that
 was building a twin engine push pull air raceing rotary. He had a landing
 gear collaps during taxie tests and I lost contact with him. Would you be
so
 kind to email me his email address?
                     Thanks in advance,
                                                   Russ Mac Farlane

 Yes that was one and the same. Tragically Dave died in a crash last
 year. The airplane is still around someplace.

 Paul Lamar

 --

Paul,

Yes it appears  rather short coupled. There are several features in the
Bell 47 'as is' that I don't like.  One is using a spine between the
planetary mount plate and the outer bearing.  The slop, though minute,
pretty much guarentees the need for an inner bearing like Dave used.

For the purposes of proper alignment only, a transmissions and  Mistral's
PSRU,  both rely on a simple nose on the end of the drive shaft after the
spline to insert into the e-shaft.
Like Mistral I have an intermediate bell housing with a central bearing
there to take any load that it might see from the prop gyroscopic
behavior.

I doubt I'll be doing acrobatics in the SeaWind but it will be
experiencing turbulence.
Distance from the PRSU front to back of the prop flange is about an inch.
From the front to the center of the MT prop arc  is about six inches


Doug in Japan


Dear Paul:
             Thank you for responding to my email I realy appreciated it.
As I remember Dave was a United captain, LAX to SYD run.
What type of crash did Dave die in??, was it in the rotary racer?.
Do you or anybody else have an email address for someone close to Dave?.
If the airplane is not crashed, 2 light weight RX8 engines with a comercial
reduction gear such as an Xesta would realy make it competiave..
For the last 35 years I have wanted to set an altitude record. 35 years
ago I could not get a preasure suit. Now I can get one, but I am runing out
of time. Time changes everything.
              Have a nice day or night,
                                             Russ Mac Farlane

Dave flew for Pan Am I think. I borrowed the huff and puff and ran it
up at Sun N Fun a few years ago.
As I recall Dave died in a Yak. Doug has his widow's  address I think.
My wife worked for United so we get to oz from time to time.

Paul Lamar

Paul or anyone,


Can someone tell me the distance the counter weight sticks out past the rear engine housing?
I want to eventually use one from a Renesis engine in case if differs from the 13B.

With a straight edge across the housing I am guessing from looking at the nut it should be about 13mm or one half an inch.

Dave died in his Fuji Beechcraft.  The plane was painted like a Japanese war plane and Dave often flew it air shows and  battled with Mustangs.
Unfortunately Sandy, Dave's wife, does not answer my mails or emails.  Give her time.

Doug in Japan

I could if I were up at the hangar :)

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.