Paul,
On your website in the PSRU section you have a picture of Dave Garber's
engine mount
plate and the sun gear drive plate attached to a object that is obviously
bolted to the
counter weight.
The object in question is a plate with some sort of cup in the center. I
forgot to ask
Dave what that was. I would guess it was for a bearing. Do you know?
He didn't use any type of torque absorber on the his turbocharged 12A.
Did
you notice any
undue vibrations when you ran it at Sun and Fun?
Doug in Japan
We never let it idle below 2000 RPM.
I think you are talking about these pictures.
The big flaw in Dave's design was not enough spread in the
prop shaft bearings. Those big props would have one heck
of a gyro bending load on the prop shaft. All he had in
there were two closely spaced giant ball bearings.
From the looks of it all the bending load was transfered to
the rear main bearing of the 12A. I would make a 3D of the
whole thing as you have the parts so you have the dimensions.
Paul Lamar
Paul;
20years ago I was building a PSRU out of the top 1/2 of a Bell 47
gear box. The project got lost during a messey divorce.
Does Dave Gaeber live in Florida?. I used to know someone in Florida that
was building a twin engine push pull air raceing rotary. He had a landing
gear collaps during taxie tests and I lost contact with him. Would you be
so
kind to email me his email address?
Thanks in advance,
Russ Mac Farlane
Yes that was one and the same. Tragically Dave died in a crash last
year. The airplane is still around someplace.
Paul Lamar
--
Paul,
Yes it appears rather short coupled. There are several features in the
Bell 47 'as is' that I don't like. One is using a spine between the
planetary mount plate and the outer bearing. The slop, though minute,
pretty much guarentees the need for an inner bearing like Dave used.
For the purposes of proper alignment only, a transmissions and Mistral's
PSRU, both rely on a simple nose on the end of the drive shaft after the
spline to insert into the e-shaft.
Like Mistral I have an intermediate bell housing with a central bearing
there to take any load that it might see from the prop gyroscopic
behavior.
I doubt I'll be doing acrobatics in the SeaWind but it will be
experiencing turbulence.
Distance from the PRSU front to back of the prop flange is about an inch.
From the front to the center of the MT prop arc is about six inches
Doug in Japan
Dear Paul:
Thank you for responding to my email I realy appreciated it.
As I remember Dave was a United captain, LAX to SYD run.
What type of crash did Dave die in??, was it in the rotary racer?.
Do you or anybody else have an email address for someone close to Dave?.
If the airplane is not crashed, 2 light weight RX8 engines with a comercial
reduction gear such as an Xesta would realy make it competiave..
For the last 35 years I have wanted to set an altitude record. 35 years
ago I could not get a preasure suit. Now I can get one, but I am runing out
of time. Time changes everything.
Have a nice day or night,
Russ Mac Farlane
Dave flew for Pan Am I think. I borrowed the huff and puff and ran it
up at Sun N Fun a few years ago.
As I recall Dave died in a Yak. Doug has his widow's address I think.
My wife worked for United so we get to oz from time to time.
Paul Lamar
Paul,
Any suggestions for a lightweight starter that will fit the 13B? This is the latest
bottleneck, before I can finish modeling the Bell housing and PSRU. I think I tossed the
1985 boat anchor that came with that housing.
Doug
They are all about 7 pounds. You have a real problem because
the Bell 47 PSRU has no room for a ring gear. You might have to install
a ring gear on the front of the engine. The DG 1 had a gear drive starter
generator in the front mounted accessory case. Not as heavy as it seemed
because it was doing two jobs. GM has some belt drive starter generators
on some new 2009 Chevy-Malibu so-called pseudo hybrids.
http://alternativefuels.about.com/od/2009hybridreviews/ig/
2009-Chevy-Malibu-Hybrid-/Malibu-Hybrid-motor-alternator.htm
"The motor/alternator of the Belt Alternator Starter
(BAS) hybrid system is driven by a high tension belt
from the engine crankshaft. It boosts power under
acceleration, charges the battery, and restarts the
engine after AUTO STOP."
I think that is your best bet.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.