Subject: Dave Garber's bell 47 PSRU.
From: Rotary Engine
Date: 2/8/2010, 3:09 PM
To: AAA Put this in the To box


 Paul,

 Any suggestions for a lightweight starter that will fit  the 13B?  This is
 the latest
 bottleneck, before I can finish modeling  the Bell housing and PSRU.  I
 think I tossed the
 1985 boat  anchor that came with that housing.

 Doug

 They are all about 7  pounds. You have a real problem because
 the Bell 47 PSRU has no room for a  ring gear. You might have to install
 a ring gear on the front of the  engine. The DG 1 had a gear drive starter
 generator in the front mounted  accessory case. Not as heavy as it seemed
 because it was doing two jobs. GM  has some belt drive starter generators
 on some new 2009 Chevy-Malibu  so-called pseudo  hybrids.

 http://alternativefuels.about.com/od/2009hybridreviews/ig/
 2009-Chevy-Malibu-Hybrid-/Malibu-Hybrid-motor-alternator.htm

 "The  motor/alternator of the Belt Alternator Starter
 (BAS) hybrid system is  driven by a high tension belt
 from the engine crankshaft. It boosts power  under
 acceleration, charges the battery, and restarts the
 engine after  AUTO STOP."

 I think that is your best bet.

 Paul Lamar


 Paul,
 That accesory drive case looks just like the one on a solar turbine. Do
 you
 know if Dave adapted it?
 Bill Jepson

 I think it was custom made by Racing Beat. Jim Mederer built aircraft
 engines
 for others as well. This one is particularly cosmetic :)


 Paul Lamar


 Paul,

 The GM Belt Alternator Starter (BAS) requires 36 volts to run.  What you
 would save on starter weight, you lose on having to carry two extra
 batteries.

 Caption for the picture reads, "The black box with the blue cable houses
 the
 36-volt hybrid battery that powers the motor/alternator for engine assist
 as
 well as restarting the engine from AUTO STOP mode. Protective cover removed
 for photo."

 Mark S.


 That certainly is a drawback for most of us.

 The batteries can be smaller as power is power regardless of the voltage.
 Battery power is a fixed function of battery weight. A starter requires
 roughly 3 HP or 2300 KW. At 12 volts that would be 186 amps.
 At 36 volts that would be only 62 amps. Certain devices like CD ignition
 systems work better with high voltage as they are already converting
 12 volts to 400 volts.

 One could use 3 small motor cycle batteries. Wired in series.
 One could also use lithium ion for a better battery power to
 weight ratio.  In some cases one would need a custom designed
 voltage switching converter to convert 36 volts to 12 volts
 for powering radio's and other stuff.

 In Doug's case he has little choice. Doug is in love with
 electricity anyway as that is his main biz :) Here is a picture
 of his electric car powered by solar wind turbines in the
 back ground. He is the perfect man to do the development.


 Paul Lamar

Paul, Do you have a guess where to get a part number and price for the
alternator/starter. I like the idea of using three riding mower batteries in
series for the starter and charging. With a composie airframe having ground
 wire requirements anyway, puting the batteries in series for charging and
starting and parallel for other functions seems doable. Also I could
segregate avionics, lighting, and engine off the three batteries. If the
cost is similar to the combined price of a new starter and alternator which
I have to buy anyway for the four rotor it sounds perfect for me.
       My airframe will be a prototype where  battery weight is useful for
adjusting CG and as an added advantage the cable weight  reduction from the
36 volt system is at least 8 pounds for a behind the seat battery location.
       I  haven't found anything more on the internet than was repored
here. The engine displacement and cranking speed comparison to a rotary will
need to determined, but it has possibilities.

george grimes

I have no idea but they will be in junkyards sooner or later.
Switching from three in series to 3 in parallel is very doable
now a days because of advances in solid state switches.

Paul Lamar


As you know, if the batteries are charged in series, they probably
should also be loaded in series as well.  If loading of the batteries
is uneven, charging may be uneven, and this can have a detrimental
effect on battery life.  One battery may end up overcharged and
another may be perpetually undercharged.

Having two different bus voltages on a small airplane limits the
flexibility of the system and can significantly reduce fault tolerance
or increase complexity.  Neither is good on an airplane that you want
to operate over large stretches of water.

Many avionics are rated for continuous operation up around 30V.  I
think I'd be tempted to go 36V with step down regulators for all of
the small components that can't handle the voltage being that high.
Or, I'd run the starter at 36V with the batteries in series and all
other operation with the batteries in parallel (at 12V).  It's quite
likely you can get a voltage regulator that charges at 12V on this
alternator.  Esp if it's a wound field alternator.


Regards,

Matt-

Well you can monitor uneven charging with electronics as well and perhaps use
variable shunts to control re charging. Sounds like a perfect
application for a PIC.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.