Subject: Dave Garber's bell 47 PSRU.
From: Rotary Engine
Date: 2/10/2010, 8:37 AM
To: AAA Put this in the To box






  Paul,

  On your website in the PSRU section you have a picture of Dave Garber's
  engine mount
  plate and the sun gear drive plate attached to a object that is
obviously
  bolted to the
  counter weight.

  The object in question is a plate with some sort of cup in the center.
I
  forgot to ask
  Dave what that was.    I would guess it was for a bearing. Do you know?

  He didn't use any type of torque absorber on the his turbocharged 12A.
 Did
  you notice any
  undue vibrations when you ran it at Sun and Fun?

  Doug in Japan

  We never let it idle below 2000 RPM.

  I think you are talking about these pictures.
  The big flaw in Dave's design was not enough spread in the
  prop shaft bearings. Those big props would have one heck
  of a gyro bending load on the prop shaft. All he had in
  there were two closely spaced giant ball bearings.

  From the looks of it all the bending load was transfered to
  the rear main bearing of the 12A. I would make a 3D of the
  whole thing as you have the parts so you have the dimensions.

  Paul Lamar


  Paul;
        20years ago I was building a PSRU out of the top 1/2 of a Bell 47
  gear box. The project got lost during a messey divorce.
  Does Dave Gaeber live in Florida?. I used to know someone in Florida
that
  was building a twin engine push pull air raceing rotary. He had a
landing
  gear collaps during taxie tests and I lost contact with him. Would you
be
 so
  kind to email me his email address?
                      Thanks in advance,
                                                    Russ Mac Farlane

  Yes that was one and the same. Tragically Dave died in a crash last
  year. The airplane is still around someplace.

  Paul Lamar

  --

 Paul,

 Yes it appears  rather short coupled. There are several features in the
 Bell 47 'as is' that I don't like.  One is using a spine between the
 planetary mount plate and the outer bearing.  The slop, though minute,
 pretty much guarentees the need for an inner bearing like Dave used.

 For the purposes of proper alignment only, a transmissions and  Mistral's
 PSRU,  both rely on a simple nose on the end of the drive shaft after the
 spline to insert into the e-shaft.
 Like Mistral I have an intermediate bell housing with a central bearing
 there to take any load that it might see from the prop gyroscopic
 behavior.

 I doubt I'll be doing acrobatics in the SeaWind but it will be
 experiencing turbulence.
 Distance from the PRSU front to back of the prop flange is about an inch.
 From the front to the center of the MT prop arc  is about six inches


 Doug in Japan


 Dear Paul:
              Thank you for responding to my email I realy appreciated it.
 As I remember Dave was a United captain, LAX to SYD run.
 What type of crash did Dave die in??, was it in the rotary racer?.
 Do you or anybody else have an email address for someone close to Dave?.
 If the airplane is not crashed, 2 light weight RX8 engines with a
comercial
 reduction gear such as an Xesta would realy make it competiave..
 For the last 35 years I have wanted to set an altitude record. 35 years
 ago I could not get a preasure suit. Now I can get one, but I am runing
out
 of time. Time changes everything.
               Have a nice day or night,
                                              Russ Mac Farlane

 Dave flew for Pan Am I think. I borrowed the huff and puff and ran it
 up at Sun N Fun a few years ago.
 As I recall Dave died in a Yak. Doug has his widow's  address I think.
 My wife worked for United so we get to oz from time to time.

 Paul Lamar





Dear Paul;
                 Do you have anay intrest in EAA???. I will be in Calif in
mid June I hope, I am in Newcastle NSW Australia. If you & your wife are
ever in Australia let me know. I will pick you up at Sydney. We could talk
rotary engins for hours & hours.
Could you please send me Dave Garber's wifes email or phone # or some way
to contact her, about Daves  rotary engine . I would like to re power Huff &
Puff with 2 light weight thrbo 13B engies & proven  PSRU. It is SHAME TO LET
DAVES DREAM DIE WITH HIM. Cost is no object now and everything will be
profesionaly enginered.
The airplane would be flying inabout 6 mounths.
                                  Thanks,
                                             Russell Mac Farlane

I am a member of EAA but I am rather disappointed in the magazine.
Frequently technically in accurate.

When you are nearly ready to fly I'll pop down to Sydney to look it over.

Dave's wife does not appear to be answering email. Doug is a good
friend so if he sends me her phone number I will pass it along by
private email.

Try mailing her at this address.

 Garber
935 Archer Grove Rd.
Athens GA. 30607

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.