Subject: Mike Wills P-port in RV4
From: Rotary Engine
Date: 2/22/2010, 2:22 PM
To: AAA Put this in the To box


 No way would that muffler you are building fit in my cowl. Nor would the
 slide throttle PP engine from your video. One of the things that sold me on
 going the rotary route in the first place was the compact size. I'd love to
 duplicate the 4 port intake on the BEC engine (minus the Airflow Perf
 injection - I'd stick with electronic injection). A PP design that hugged
 the engine like the BEC intake would be best of both worlds.

 Mike Wills

 I tried it on tubing and it worked but you have a good point there.
 I stand corrected on surfaces. Of course the glue will melt.

 Looks like one would need a layer of fiberfrax with a .010" thin
 sheet of SS mechanically fastened to the
 fiberglass with SS screws or monel pop rivets.

 Another alternative is put some $10 Home Depot steel wall heating
 register near the exhaust pipes. That will let out some of the heat.
 Here is a typical register. You can throw away what you don't need.
 If it melts the paint you could get it chrome plated.

 McMaster Carr has micro perforated 316 SS sheet 35 gage
 which is .0075" thick with a bunch of tiny .009" dia.
 holes that will let out the heat. Rather expensive
 at $170 for 22 by 24 inch sheet. However this is
 an elegant solution to a skinny cowl :)

 They also have 304 SS .024" thick with .062" dia. holes for
 about $68 for a 36" by 40" sheet. 39% open area.
 This appears to be the best bet.

 If you make a custom slide it will fit. The trick
 is to weld the runners directly to the outer cover.
 Like we did on Mark Supinski Mustang.
 Here are some 3Ds.


 That muffler won't fit but a 4.5 inch diameter tang muffer
 might.

 --------------------------------------------------

 Here is a second way Mike.
 Can anybody come up with a third way with equal length
 22" runners? Must be a 3D rendering :)

 Paul Lamar

Paul,

Out of curiosity, how wide is Mike's cowl?

Mark S.
Austin

About 24 inches. I don't think Van is still selling the RV4. I could be
wrong. There are a lot of complaints about the cockpit being too narrow.
The RV8 is the preferred replacement for a tandem air plane and
the cockpit  and the firewall are much wider.

The RV4 with a narrow cowl is a challenging packaging problem
and both Mike Wills and Brian Trubee did a good job.


Paul Lamar


The RV-4 is still listed:

http://www.vansaircraft.com/public/kitprice.htm

My RV-4 flying friend claims the RV-4 is preferable in certain ways
even though (because?) the fuse is narrower.  He likes the way his
flies better and likes the landing gear better as well.

The RV-4 is still the basis for the Harmon Rocket.  You order much of
the RV-4 from Van's, minus the stuff that Harmon sells to "Rocketize"
the airframe..  "When you purchase a modification kit to build a
Rocket II from John Harmon the kit is an extension of the RV-4 kit
which is purchased from Van's.  Please review the PARTS/MATERIAL  page
for details of what to order.   "

http://www.harmonrocket.com/

Along those lines, I think it would be interesting for someone to
Rocketize the airframe of an RV-4 and instead of putting an IO-540 on
it, use a 20B..


Matt-


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.