Subject: Brian Trubee's FANTASTIC 13B powered RV4
From: Rotary Engine
Date: 2/25/2010, 5:58 PM
To: AAA Put this in the To box


Here's a photo of the cowl, it's a few months old, so I'll get a couple
of new photos today. I'm pretty much waiting to get my registration
paperwork back and set up an appointment with a DAR.

Brian Trubee

Wow! Cool Brian. That is a fine looking airplane.

Take some pictures of the cooling scoops for me.

Paul Lama

I'm looking forward to seeing more pictures too, both cowled and
uncowled.
I'm really curious to see what your cooling/muffler install looks like.
Looking good Brian!

Mike Wills


The muffler is buried in a space between the original bottom of the
fuselage and the new lower bottom of the fuselage, along with the
coolant and oil cooler lines. The heat exchangers are mounted under the
main spar at an angle and form a wedge shape plenum between the fuselage
bottom and heat exchangers. I'll get some more photos today.

The muffler is a Hushpower and is really quiet. I put a lot of heat
shielding around the muffler and exhaust system along with a good amount
of air space, and tried to provide a lot of air movement to carry heat
away from the exhaust system. I originally wanted to put the heat
exchangers under the engine, but felt that it got too busy inside the
cowl and there were too many things exposed to the heat of the exhaust
and that that configuration required too many compromises with airflow
through the heat exchangers. Right now, running the engine up on the
ground at 50 degrees, even without the intake scoop and cowl flap
completed, I have a hard
time getting the temps up over 200 degrees. I
expect things will change when the air temperature gets up into the
90's.

If you decide you want to try making an aluminum cowl yourself, I can
send you a video by John Glover on how to do it,a few sketches on how to
design the cowl pieces and offer any advice you may need. I never made
a cowl or anything else on an english wheel before this.( OK, I made a
few "practice" cowls before this one). But, with Harbor Freight selling
English wheels for under $325 now, and enough aluminum to make a cowl
for around $250, it's kind of hard to go wrong. You can fly your
airplane with the old cowl and make a new one in your garage or basement
in the meantime. .


Working an english wheel is nice and relaxing- it's
quiet and clean- no smelly , sticky, itchy fiberglass and resin.

I made one cowl about ten years ago and gave it away to a guy in Oregon
after I decided to use a 16 inch Mustang II spinner. When I made it, I
found a guy down in Graham, Washington who had built a really nice
English Wheel in his machine shop. He offered to let me come down and
use it. He watched my progress for a while, shook his head, and said
good luck.

After few hours he came back out and was amazed that I had
actually made the shapes that I wanted to make. He told me that he had
never been able to figure out how to use the wheel that he had made. I
guess he had never watched the video. Anytime you start something youv'e
never attempted before, there's always the apprehension that you'll not
succeed, but if you are persistant you'll pick up a new skill. Isn't
the the way you felt when you started your RV-4?

Brian Trubee
--
Brian,

Having tried my english wheel I can really appreciate your skill.  How
can I get the Glover video?  Is it possible to work thin .025 material
or only thicker material.  My .040 door parts are ok but the .025 cabin
sides need some hammer and dolly work to take out "oil cans".

Dan F

Patriot II (second prototype almost done)



The thinner the material, the faster it will "move", and the same goes
with the softer materials. The thickest I've worked with is .063 6061
T6. My present cowl was made with .050 6061 T6.  You can work with
really thin material, you just adjust the pressure on the wheels
accordingly.  I jumped right into building my cowl. You might want to
just play around with some scrap before you commit to building your
project. Here's a tip I found when working a larger piece- get a little
bit if shape on the end, because if you try to put some shape in the
middle, it turns the piece into a curly-cue and is tough to work.
Starting at the end will get the piece to take the correct curve.



Brian Trubee


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.