Clive Ure wrote:
Paul,
Are there any types of 20B engine that are 'lemons' that
I should not consider for my 337 project. Any years better than
others?
Regards
Clive
Not that I know of. The only rotary engine I know that might be
labeled a lemon
was the 2004-2006 RX8 engine and it had nothing to do with the engine
it self. Mazda merely cut back too far on the apex seal oil supply.
Fixed around 2007 with three instead of two oil injectors per rotor.
Of course
we mix 2 cycle oil in the fuel to bypass that situation.
The 1989-1990 initial Turbo II engine cracked the exhaust manifold
with regularity. Fixed more or less in the 1991-1992 Turbo II engines.
A lot of Turbo 3rd gen guys blew them up by boosting the engine
without adjusting the fuel supply. They ran lean. The 3 piece apex
seal
design did not help. Done away with in the RX8 engine with a 2
piece design now retrofitted to all engines.
Paul Lamar
Thanks Paul,
1.Shall I use the existing turbo(s), I want to turbo normalize so I
want to modify the waste gate to manual operation controlled by the
pilot.
2.I would like to use the existing injectors? and the computer to
control them or do you suggest something else?
3.I like the slide throttle concept like the one attached here, is
there anyone who can make one for me?
I have read Tracy's book and your 'cooling' book.
I really value your opinion.
Thanks
Clive
You might have trouble with the stock turbo's. They are not
up to continuous high power. Especially at 12K and above where
the back pressure is down. They tend to over rev and the turbines
blow. At least that happened on the turbo 2 rotors.
I would change them out for one AC turbo.
Tome Parkes on here has a 3 rotor with an AC turbo in a Lancair ES.
Paul Lamar
Sorry for my ignorance...what is an "AC Turbo"? Thanx...
Gene Kahn
Sorry I should have spelled it out. I meant AirCraft turbo.
Aircraft turbochargers come in different combinations
compared to an automotive turbo. A turbocharger in a car
is designed for rapid turbine RPM acceleration and
intermittent use. This is done in several ways. An
exhaust gas nozzle is built in to speed up the exhaust
gases before they impinge on the turbine. The diameter of
the turbine and the diameter of the compressors are
adjusted to have this happen.
What results is a turbocharger design that will over speed
and blow up if the engine is run at 80% power for hours on
end. Exactly what is required of an aircraft engine.
Another factor is what happens when you climb. Sea Level
pressure is about 15 psi. Exhaust gas pressure can be 30
psi or more. That means the turbine is seeing a only a 15
psi pressure differential across the turbine at sea level.
If you climb to 12,000 feet air pressure drops so the
pressure across the turbine increases to say 20 psi. That
causes the turbo charger RPM to speed up and may exceed the
red line on the turbine so the blades may fly off.
The same parts and materials are used in aircraft turbo
chargers but the diameters of turbine and compressor are
adjusted and or the nozzle so the turbine will not exceed
the RPM red line under high altitude conditions for hours
on end.
The stock Mazda waste gate is a device that is supposed to
prevent this but it is not effective enough for aircraft
use. It can be locked wide open on a stock Mazda turbo
charged engine and the turbine will still fail in just a
few hours at 12,000 feet.
I recommend a book called Turbochargers by Hugh Macinnes H.P. Books.
http://www.amazon.com/Hugh-MacInnes/e/B001KML952/ref=ntt_athr_dp_pel_1
Paul Lamar
Thank you for that considerable help!
Gene Kahn
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.