Subject: Need your advise to purchase a tig welder
From: Rotary Engine
Date: 3/13/2010, 7:48 AM
To: AAA Put this in the To box

Since i joined the group i know several of you are doing
some tig  welding and i need some advise and comments
to find the cheapest  unit and the appropriate one for
my project,i will have to weld my  drive housing with
reinforcement gusset of 1/4 " thickness aluminum  plate
and to 1/2 plate i found lot on the market true EBAY
and CraigLists.com.

I handle pretty good the acetylene torch ,  have
welded 2 chromemoly tubing  Dafhne frames and  with
a few practice i am convince i will be fine to
handle  the tig welding.

As per some expert they say i will need  minimum
250 amps for the 1/2" plate

Jean  Prudhomme


Jean,
You do not want the cheapest  welder you can find, especially to weld Al.
The low cost ones  usually only have a 20% duty cycle. That means only 12
minutes per hour. To  weld the 1/2" Al., I would look for a unit that gives
40 to 50% duty  cycle. Cost likely $3000 and up a bit.

Dale  Davies


Jean,
1/2" aluminum plate is the tough part. I have a Miller Syncrowave 250 that
would do it but it cost 3K+ when I bought it. If cost is your biggest
sticking  point I would suggest looking into one of the inverter technology
welders from  Miller or Lincoln. When looking be sure to mention the need
to weld
1/2"  aluminum plate which may be too tough for them. You will need a water
cooled  torch I'm sure. That isn't something that comes with the inverter
style welders  from either manufacturer I believe. The Syncrowave products
are often sold in  package deals which can often be negotiated on price.
That
may be your best bet,  but don't think anything with the capability to weld
thick aluminum will be  cheap. Note also that you will need at least a 50
amp 220 service in your  shop.
Bill Jepson


I think you need to run through this again. Perhaps the bracing can be 1/4"
angle stock screwed or bolted in place. Or the plate stock could be a
stiffer alloy?

You will be hard pressed to come up with thick plate in a weldable alloy. I
have a 600 AMP Hobart unit that I can weld anything with. But I would not
attempt the 1/2" plate idea. Even with a water cooled torch you will be
standing on the control pedal, and the filler rod will be dribbling into a liquid
while still a foot from the work. You probably want to preheat the plate
stock just in the area behind each weld bead, to minimize warpage, or, you
will have a 1/2 thick aluminum potato chip. Use a leather apron and arm guards.
The light will go right through your clothes and give you a nasty sunburn.
Use real dark glass in the mask not the instant darkening crap. Goggles with
side shields under the mask. Light bouncing off a wall after one flash and
your eyes will feel like they are full of sand. You need not be looking at
the wall. Not to worry, it goes away after only three days.

Never flip the mask up to look at the nice bead. They pop every so often
and spray out chunks of metal. I used to have my own parking space at the
hospital from this stuff.

Argon works on anything. CO2 only works for steel. Practice welding beer
cans together.

Signup for a welding course at a local trade school. Very cheap, the very
best equipment.
You have been paying for that stuff with your taxes, take advantage of it.
TIG is almost too easy to learn. Same as gas welding but you can control the
temperature with your foot, in most cases or with a trigger on the handset.
Just dead easy. Preheat, and post heat 4130 or it cracks. You can also
lease machines for months at a time, and every so often the folks sell off the
lease machines. My ex lease Hobart was $600.00 Saved about $4,000.
Once you build up your knowledge base, you can look at used machines. With
Obama in charge there are thousands of used machines available.

Find somebody that has one (like Me) and buy them a bottle of gas for some
welding instruction.

Make that a double 50 AMP breaker and only the welder goes on that one

Lynn E. Hanover

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.