Subject: Need your advise to purchase a tig welder
From: Rotary Engine
Date: 3/13/2010, 6:50 PM
To: AAA Put this in the To box

 Since i joined the group i know several of you are doing
 some tig  welding and i need some advise and comments
 to find the cheapest  unit and the appropriate one for
 my project,i will have to weld my  drive housing with
 reinforcement gusset of 1/4 " thickness aluminum  plate
 and to 1/2 plate i found lot on the market true EBAY
 and CraigLists.com.

 I handle pretty good the acetylene torch ,  have
 welded 2 chromemoly tubing  Dafhne frames and  with
 a few practice i am convince i will be fine to
 handle  the tig welding.

 As per some expert they say i will need  minimum
 250 amps for the 1/2" plate

 Jean  Prudhomme

 Jean,
 You do not want the cheapest  welder you can find, especially to
 weld Al. The low cost ones  usually only have a 20% duty cycle. That
 means only 12 minutes per hour. To  weld the 1/2" Al., I would look
 for a unit that gives 40 to 50% duty  cycle. Cost likely $3000 and
 up a bit.

 Dale  Davies

 Jean,
 1/2" aluminum plate is the tough part. I have a Miller Syncrowave
 250 that would do it but it cost 3K+ when I bought it. If cost is
 your biggest sticking  point I would suggest looking into one of the
 inverter technology welders from  Miller or Lincoln. When looking be
 sure to mention the need to weld 1/2"  aluminum plate which may be
 too tough for them. You will need a water cooled  torch I'm sure.
 That isn't something that comes with the inverter style welders
 from either manufacturer I believe. The Syncrowave products are
 often sold in  package deals which can often be negotiated on price.
 That may be your best bet,  but don't think anything with the
 capability to weld thick aluminum will be  cheap. Note also that you
 will need at least a 50 amp 220 service in your  shop. Bill Jepson

 I think you need to run through this again. Perhaps the bracing can
 be 1/4" angle stock screwed or bolted in place. Or the plate stock
 could be a stiffer alloy?

 You will be hard pressed to come up with thick plate in a weldable
 alloy. I have a 600 AMP Hobart unit that I can weld anything with.
 But I would not attempt the 1/2" plate idea. Even with a water
 cooled torch you will be standing on the control pedal, and the
 filler rod will be dribbling into a liquid while still a foot from
 the work. You probably want to preheat the plate stock just in the
 area behind each weld bead, to minimize warpage, or, you will have a
 1/2 thick aluminum potato chip. Use a leather apron and arm guards.
 The light will go right through your clothes and give you a nasty
 sunburn.
 Use real dark glass in the mask not the instant darkening crap.
 Goggles with side shields under the mask. Light bouncing off a wall
 after one flash and your eyes will feel like they are full of sand.
 You need not be looking at the wall. Not to worry, it goes away
 after only three days.

 Never flip the mask up to look at the nice bead. They pop every so
 often
 and spray out chunks of metal. I used to have my own parking space
 at the hospital from this stuff.

 Argon works on anything. CO2 only works for steel. Practice welding
 beer
 cans together.

 Signup for a welding course at a local trade school. Very cheap, the
 very best equipment. You have been paying for that stuff with your
 taxes, take advantage of it. TIG is almost too easy to learn. Same
 as gas welding but you can control the temperature with your foot,
 in most cases or with a trigger on the handset. Just dead easy.
 Preheat, and post heat 4130 or it cracks. You can also lease
 machines for months at a time, and every so often the folks sell off
 the lease machines. My ex lease Hobart was $600.00 Saved about $4,
 000. Once you build up your knowledge base, you can look at used
 machines. With Obama in charge there are thousands of used machines
 available.

 Find somebody that has one (like Me) and buy them a bottle of gas
 for some welding instruction.

 Make that a double 50 AMP breaker and only the welder goes on that one

 Lynn E. Hanover


 Hi Jean,
 Lynn makes some good points. Another source for starter instruction
 is at the
 welding supply shop. Some times they will put on courses. I took one
 while in
 a street rod club. They should give you a little certificate. Their
 idea is to
 introduce you to the machines and hopefully sell you one. They may
 sell the
 "school" machines as demos now and then. You get to use the newest
 machines
 and try the one you may be interested in. 1/2" will be tough and
 require multi
 passes. Again I state, look at the duty cycle and the current at
 that duty
 cycle. Go the highest your budget will allow. A large machine
 running at a
 lower duty cycle will do a better job and last longer. Too small and
 you will
 be frustrated. You do not want to get into an industrial machine
 that is
 advertised with a 100% duty cycle either. These are OK in a
 production shop.
 Outside that and you are wasting money.

 Dale Davies

Last month, I took an EAA Sportair TIG Class.  Check their website for
classes.

Don


Jean,

You can weld 1/2" plate with DC reverse polarity.  It takes some practice,
but it works great on thick plate.

Mark S.

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.