Since i joined the group i know several of you are doing
some tig welding and i need some advise and comments
to find the cheapest unit and the appropriate one for
my project,i will have to weld my drive housing with
reinforcement gusset of 1/4 " thickness aluminum plate
and to 1/2 plate i found lot on the market true EBAY
and CraigLists.com.
I handle pretty good the acetylene torch , have
welded 2 chromemoly tubing Dafhne frames and with
a few practice i am convince i will be fine to
handle the tig welding.
As per some expert they say i will need minimum
250 amps for the 1/2" plate
Jean Prudhomme
Jean,
You do not want the cheapest welder you can find, especially to
weld Al. The low cost ones usually only have a 20% duty cycle. That
means only 12 minutes per hour. To weld the 1/2" Al., I would look
for a unit that gives 40 to 50% duty cycle. Cost likely $3000 and
up a bit.
Dale Davies
Jean,
1/2" aluminum plate is the tough part. I have a Miller Syncrowave
250 that would do it but it cost 3K+ when I bought it. If cost is
your biggest sticking point I would suggest looking into one of the
inverter technology welders from Miller or Lincoln. When looking be
sure to mention the need to weld 1/2" aluminum plate which may be
too tough for them. You will need a water cooled torch I'm sure.
That isn't something that comes with the inverter style welders
from either manufacturer I believe. The Syncrowave products are
often sold in package deals which can often be negotiated on price.
That may be your best bet, but don't think anything with the
capability to weld thick aluminum will be cheap. Note also that you
will need at least a 50 amp 220 service in your shop. Bill Jepson
I think you need to run through this again. Perhaps the bracing can
be 1/4" angle stock screwed or bolted in place. Or the plate stock
could be a stiffer alloy?
You will be hard pressed to come up with thick plate in a weldable
alloy. I have a 600 AMP Hobart unit that I can weld anything with.
But I would not attempt the 1/2" plate idea. Even with a water
cooled torch you will be standing on the control pedal, and the
filler rod will be dribbling into a liquid while still a foot from
the work. You probably want to preheat the plate stock just in the
area behind each weld bead, to minimize warpage, or, you will have a
1/2 thick aluminum potato chip. Use a leather apron and arm guards.
The light will go right through your clothes and give you a nasty
sunburn.
Use real dark glass in the mask not the instant darkening crap.
Goggles with side shields under the mask. Light bouncing off a wall
after one flash and your eyes will feel like they are full of sand.
You need not be looking at the wall. Not to worry, it goes away
after only three days.
Never flip the mask up to look at the nice bead. They pop every so
often
and spray out chunks of metal. I used to have my own parking space
at the hospital from this stuff.
Argon works on anything. CO2 only works for steel. Practice welding
beer
cans together.
Signup for a welding course at a local trade school. Very cheap, the
very best equipment. You have been paying for that stuff with your
taxes, take advantage of it. TIG is almost too easy to learn. Same
as gas welding but you can control the temperature with your foot,
in most cases or with a trigger on the handset. Just dead easy.
Preheat, and post heat 4130 or it cracks. You can also lease
machines for months at a time, and every so often the folks sell off
the lease machines. My ex lease Hobart was $600.00 Saved about $4,
000. Once you build up your knowledge base, you can look at used
machines. With Obama in charge there are thousands of used machines
available.
Find somebody that has one (like Me) and buy them a bottle of gas
for some welding instruction.
Make that a double 50 AMP breaker and only the welder goes on that one
Lynn E. Hanover
Hi Jean,
Lynn makes some good points. Another source for starter instruction
is at the
welding supply shop. Some times they will put on courses. I took one
while in
a street rod club. They should give you a little certificate. Their
idea is to
introduce you to the machines and hopefully sell you one. They may
sell the
"school" machines as demos now and then. You get to use the newest
machines
and try the one you may be interested in. 1/2" will be tough and
require multi
passes. Again I state, look at the duty cycle and the current at
that duty
cycle. Go the highest your budget will allow. A large machine
running at a
lower duty cycle will do a better job and last longer. Too small and
you will
be frustrated. You do not want to get into an industrial machine
that is
advertised with a 100% duty cycle either. These are OK in a
production shop.
Outside that and you are wasting money.
Dale Davies
Last month, I took an EAA Sportair TIG Class. Check their website for
classes.
Don
Thank,s very much for your advises
Jean Prudhomme
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.