Hi you guys
I know there are RWS controller users on this list.
Hopefully no one has replicated this failure mode in their installation.
Here is the link
http://www.eaa.org/news/2010/2010-03-08_landing.asp
Basically the mounting nut was only a few threads on and despite a locking
washer, worked lose and fell on to the circuit board and moved around
until
it shorted something out. Despite two separate circuits' the short
downed
the plane fortunately no one was hurt.
It is apparent that it must have shorted the main feed to both sides, as
the
plane was trailerd to the home field and the fault identified.
The pilot is to be congratulated for making a safe landing causing no
damage
to himself/others or his plane, but more so for sharing the cause of his
misfortune.
Clive ...........England
A drop of RTV around and on top of the nuts would have prevented
this. I am glad it was not a rotary.
Soobs vibrate harder than rotaries.
It is also a good idea to mount your computer with rubber shock
mounts. Search "rubber isolators" in McMaster Carr.
Use three of the 2 pound versions. I am sure the box weighs
much less than 6 pounds. So add a bit of steel sheet to the box
and get it up to six pounds. That gets the resonant
frequency as low as possible.
" Vibration-Damping Mounts? Isolate vibration, shock, and
noise transmitted to and from machinery. They reduce maintenance
costs, prolong equipment life, and protect floors. Performance
is measured by deflection (the distance the mount material moves
when subjected to force). Generally, the higher the deflection
rating, the greater the vibration, shock, and noise isolation."
Paul Lamar
Paul,
No shock mounts. Tracy is adamant about the need to ground the case. I'd
like to see it shock mounted too. I know you are going to provide all sorts
of options for getting around that. But you and I didn't design the box.
Mine is mounted per the designer's instructions.
Mike Wills
That is a very strange position for Tracy to take. Looks like he
paid a price for that position. One can ground the case and
still use shock mounts. Are you sure he is against shock
mounting per se or do you think he just thinks it won't be
grounded? In plastic air planes it must be grounded with
a wire in any case.
Just about all electronic equipment is shock mounted in
air liners and has been for decades.
Braided steel sleeve or ribbon is usually used for grounding.
Here is perhaps a better shock mount that grounds as well
as vibration isolating. No need for ballast as it has a
lower load rating.
------------------------------------------------------------
Here is a scan out of an Aircraft Systems Maintenance text book.
Between Robin and I we have a huge collection of air craft books.
Paul Lamar
Details on the failure from Jon Finley:
Tom Walter
Hi all,
I have confirmed the cause of my power failure last weekend. Long story short - it was
builder error. When you install a locknut on a bolt, you MUST ensure that there is at
least a thread or two coming all the way thru the nut. If not, it will eventually vibrate
free. I am guessing that I did not look at these nuts after installation due to the
difficulty of seeing anything in this area. No excuse - get a mirror or whatever is
required and visually confirm this type of thing.
Longer story: To mount my EFI controller (computer in a metal box), I mounted two bolts on
the underside of my header tank, two holes in the controller box, and then put locknuts on
each of these bolts. One of these nuts (and washer) came off the bolt and got down into
the electronics. I assume they bounced around in there for awhile before finding the ideal
location to cause a short which shut everything down.
I have changed my mounting method and now have nutplates inside this "box".
Please; learn from other's mistakes cause you don't have enough time to make them all
yourself!!
Jon Finley
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.