3) Anyone know parts numbers for the water and oil pumps from the 20B or maybe a supplier you've used that caries them? Jay Hi Jay; >From what little I remember, the 20B's were somewhere between 2nd and 3rd gen. A good place for used parts and information is rx7club.com. See also nopistons.com There are several forums you can search or post a want to buy thread: http://www.rx7club.com/forumdisplay.php?f=95 http://www.rx7club.com/forumdisplay.php?f=99 http://www.mazdamotorsports.com You can supposedly still order Cosmo/20B parts through your Mazda dealer. Some people seem to have a full Cosmo parts fiche. See this thread for hints (I should have bought that car): http://www.rx7club.com/showthread.php?t=788077&highlight=cosmo Some of the engine parts are here: http://cp_www.tripod.com/rotary/pg20.htm Cosmo: http://cp_www.tripod.com/rotary/pg09.htm possibly: http://www.partsnet.com.au/members.html Cheers Cary Paul, Here are some photos of the original water pump and housing side by side with the one I got from Atkins. I also included one of the front end housing. The oil pump is going to fit. So for now I'm just dealing with the water pump issue. Dan at Atkins suggested an 86'-91' pump and housing would fit the 20B without any fabricating or cutting. Can you corroborate this? Thanks Jay Your original pump is fine Jay. No need for the 3rd gen cartridge besides the that fact that it does not fit the 20B water pump housing. I'll take a closer look at my 20B out in the hangar and see if I can find any disadvantages to sticking with the original pump. You may have to cut it down to fit under your cowl but that would be true of a 2nd or 3rd gen water pump housing as well. Paul Lamar The front cover looks unique to the 20B but I am not sure. Mainly in the area of the oil drain back for the sequentially turbos. Please take a picture of the front cover both from the front and rear so we can tell if it will fit a 2nd gen water pump housings. Also please take a picture of the 20B front end housing from the front. The cartridge Dave Atkins sent you is a 2nd gen 8 bolt version. In order to use that you would need a 2nd gen water pump housing which may or may not fit your front cover. The only drawback I can see sticking with the 20B WP pump is the difficulty in finding a new cartridge if it develops a leak or the bearings go out. They can be pressed apart and the bearings replaced but that is what most people don't do. They just replace the cartridge. Paul Lamar Paul, The 13b water pump housing will fit on the 20b, but the 13b's impeller is smaller. Also, the Renesis water pump (removed from the front cover) will also fit the 20b. The Renesis entire front cover will fit, but it requires some machine work for it to clear the 20b front counterweight which is larger than the Renesis' counterweight and it interferes with some of the front cover casting. If you machine it for adequate clearance, then you are into the bolt head recesses which then must be welded up, but by this point, we're probably beyond what most people would be willing to do for the limited benefits of the Renesis front cover. Also, the Renesis front cover has a different shape and spacing around the oil pan. Not a problem if you're building a custom oil pan anyway. The easiest route is to cut the Renesis pump housing from the front cover (if you want to run the Renesis water pump). Who was it that commented about removing and replacing the 20b exhaust inserts. Having gone down that road, my recommendation is DON"T DO IT unless you're planning on turbo-charging your engine. I changed out the 20b exhaust inserts for 13b turbo inserts. Now I'm pulling my hair out trying to get a muffler that will handle the torture of the rotary's exhaust and still quiet things down. Word has it that the splitter inserts are good for a 5db noise reduction. I constantly get the comment from people that they can hear me coming long before they can see me. Not exactly the image I want to portray. You can be sure that my new engine will retain the stock exhaust inserts. Mark S. Are you talking about removing the RX8 engine water pump housing from the RX8 engine front cover? In other words sawing it off? That sounds like a good idea except for the cost of an RX8 front cover. The RX8 WP cartridge will not fit the 20B water pump housing. Paul Lamar