Hi, I really enjoyed your 35 MPG rx-8, and I was wondering if instead of a
third smaller rotor if you could turn off one of the 2 rotors?
If you wrote an article and I couldn't find it I apologize.
Also, subscribe :)
Yes. The drawback is you still have the friction of the dead rotor.
Paul Lamar in Bartow
Paul,
The rotary is obviously compact and reasonably light, which makes it
attractive for aircraft, but the efficiency problems you are trying to
address are what limits its popularity in cars.
Consider that a garden variety BMW 328i sedan already gets 35 mpg at 65 mph,
even though it weighs at least 300 pounds more than an RX-8 and at has least
five percent more aerodynamic drag. And the 328i is also geared too short
for optimal fuel economy, in order to retain some top-gear acceleration.
The next generation 3-series will likely include a four-cylinder turbo with
probably more power than the 230 hp of the 328 and 65-mph fuel economy
upwards of 40 mpg. Though I'm sure that the rotary can, and will, be
improved, the Wankel is competing against a moving target.
Csaba Csere
Yes I am well aware of the current BSFC problems with the current rotary
engine in automotive applications. However the moving target is not moving
very fast. The piston engine is near the end of its development cycle while
the rotary is just getting started.
We just did a video interview with the CEO of Wankel Supertech in Germany
and
they have apparently solved the low power BSFC problem by a slight change in
the R/e ratio. Compression ratio is now up from 10:1 to 14:1. They are
claiming a BSFC of 240 grams/KW-Hr. That translates to .389 BSFC down from
.52 BSFC. The current RX8 gets about 25 MPG at 65 MPH so that alone
would increase it to 32 MPG while retaining the size and weight advantages
of the rotary. A mere switch to a paddle shifted, all mechanical auto
transmission would further improve the steady speed MPG on the RX8 by
lowering the freeway cruise RPM.
The rotary remains the best engine to apply the turbo compound principle
as there is no exhaust kinetic energy lost to the exhaust valve.
That positions the Wankel engines as potentially the most efficient
portable internal combustion engine of all time shy of large electrical
turbo compound (AKA bottoming cycle) electrical power plants. These plants
are 60% efficient by using the waste heat in the exhaust to generate steam
for steam turbines.
Half the kinetic energy in the exhaust is currently lost in the exhaust
valve. Diesel engines are now embracing the turbo compound configuration
despite the exhaust valve.
Car engines appear to be shortly forced into this configuration by misguided
political considerations :) CO2 is not a pollutant. It is essential
for life.
Ansdale has a better chart on this compression ratio thing but you will have
to wait for it until I get back to LA and can scan it.
Paul Lamar in Bartow
Paul,
We'll see if piston engine development is tapped out over the next few
years. The new EPA fuel economy standards that were just announced will
raise the mandatory corporate average fuel economy from 2010 to 2016 by
around 35 percent. The new standards are sized based, so this improvement
won't be achieved via downsizing. Most of it will come from powertrain
improvements. The easiest approaches are down-sizing combined with
turbocharging and adding more transmission speeds.
If I recall correctly the biggest problem with rotary efficiency is the
inherently high surface-to-volume ratio of the combustion chamber. The high
heat loss that this produces helps the rotary's tolerance for low octane
fuels, while also hampering its BSFC.
That said, your analysis of the rotary's suitability for turbo-compounding
seems sound. The question will be whether that approach will be able to
offset the engine's inherent inefficiency and produce a better result than
one of the new turbo piston engines.
We shall see.
Csaba
We will all be driving around in Smart cars in a few years unless we get
rid of the jerk :)
Paul Lamar @ Sun n Fun
I know it's widely held that the rotary engine has inferior surface to
volume ratio.. I wonder, however, whether that is somewhat
ameliorated by not spreading the heat load across as many cylinders.
The hot portion of the chamber stays hot. In a recip, the combustion
chamber is cooled a bit with every intake charge, and I imagine this
worsens the thermal efficiency.
Regards,
Matt-