Subject: P-port 3-rotor status report.
From: Rotary Engine
Date: 4/30/2010, 5:01 PM
To: AAA Put this in the To box



 Mark,
 Hows is the p-port 3 rotor going?

 Paul



 Mark Steitle wrote:

 Hi Paul,

 The 3-rotor is coming along just fine.  I flew it last Sunday after
 replacing the water pump (old pump started dripping coolant from the
 shaft/seal).  However, I replaced it with a spare 20B pump, not the
 Renesis
 that I've been working on.  That will come later.  I'll be sending you $
 for
 an inlet/outlet adapter.

 As for how it is running, I would say it is running fair.  It is rough at
 around 2000 rpm.  I'm seeing a low EGT on rotor #1, which I will try to
 adjust using EC-2 mode 4.  If I can't get it to adjust, I will have to get
 the injectors cleaned.

 You may remember that I'm running 3 MSD 6-A ignitions.  Those are working
 out great, but I'm not convinced they're worth the weight penalty.  I've
 started the engine and heard it running on 2-rotors (fouled plug), only to
 clear up a few seconds later.  I checked the plugs after Sunday's flight
 and
 they looked better then the trailing plugs which are still being fired by
 the EC-2.  So, I don't think the plugs will have any trouble handling the
 multi-spark environment.  But then I took it easy as I've made a number of
 changes lately and I'm still a little nervous.  It starts similar to the
 old
 engine, except it requires less fuel (no priming).  I turn the mixture
 knob
 to about 3 o'clock position and hit the starter, then return the knob to
 12
 o'clock once it starts.  Very nice!  Once warmed up, just hit the starter.

 One of the biggest successes is the new tangential muffler.  It is much
 quieter than any of my previous mufflers.  However, it was beginning to
 bubble the paint on the lower fuse, so I had to add a turn-down piece.
 Solved the problem.

 One side note... my old engine was plagued with oil leaks.  I think the
 oil
 was seeping through the base of the housings (the area between the oil pan
 flange and the outside the o-ring perimeter).  I didn't use any sealant in
 this area when assembling my first engine.  This was a big mistake.  Lynn
 H.
 pointed out that this is a common mistake from novice rotary builders
 (thanks Lynn).  So, I used Hylomar on these areas on my new engine... and
 no
 leaks!  Life is good!

 Cooling seemed a little higher than I would have liked to see on climb
 out,
 but they came right down once I leveled off.  OAT was 78*, oil got up to
 205, but dropped to 175 in level flight.  Water was 157* in level flight.
 But I was running it easy, so I'll be watching the temps very closely in
 future flights.  In retrospect, I climbed out at 85 rather than 110 like
 usual.  So, I'll have to keep the speeds up and see how the temps look.

 See ya,
 Mark

 Glad to hear it about the muffler. Sorry about the pun.
 Does it have the central cooling tube?
 Picture?

 Paul


 There is no cooling tube as the oil cooler is too close (need to move that
 forward).  However, it does have an internal baffle (inconel 625) that
 consists of a tube which has 109 1" diagonal slits cut in it.  One edge of
 the slits was then dimpled inward to form 109 D-shaped holes for the
 exhaust
 to exit through.  I can inspect the inner baffle with an inspection camera
 through the three inlets.

 Mark


 I think we need to add that muffler inspection procedure as a
 preflight inspection. The length of the inspection camera neck
 is 3 feet long so keep that in mind when designing your exhaust
 system. If you use the cooling tube that would allow external
 inspection of that device.

 You don't want this to happen to your muffler.
 Cheap insurance for $100.

 Paul Lamar


 Yes, I already have the inspection camera.

Mark

UPDATE:  After an inspection of the deep dark bowels of my tangential
muffler, I flew for about 45 minutes today.  Temps on the ground were in the
upper 80's, at 3000 MSL the OAT was 68*-70*.  I climbed out at 105kts
indicated and oil temps stayed around 195*F, water was 175*F.  (I measure
the oil temps out of the engine as well as the return oil temps.  The oil
out temp was 235, so I was dropping 40* through the oil heat exchanger.)
After leveling off, the temps dropped down to 160-165* for coolant,
170-175* for oil.  I confident that at normal cruise altitudes (8-10,000
msl)  the oil temps should be down closer to the magical 160* number.

There must have been a piece of crud in one of the injectors for the #2
rotor because the EGT was 400-500* lower than the other two.  The #2 EGT
gradually increased and finally got to where the other two were at, approx
1600-1650*.

It still needs some tuning but a low ceiling prevented climbing above 3000
msl.

All in all, a good flight.

Mark S.

What kind of performance numbers and fuel burn are you seeing Mark?
Rate of climb? Cruise speed. Cruise RPM. Max RPM?

Are there two injectors per rotor or just one?

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2009 All world wide rights reserved.