Subject: Atmel and ZBasic EFI and data acq-displays
From: Rotary Engine
Date: 5/13/2010, 4:00 PM
To: AAA Put this in the To box


 I would see creating my own digital cockpit display(s) as an
 interesting winter project.
 The programming does not scare me; since I earned a good share of my
 living for 30 years writing software..  However, I would need to be
 brought up to speed on on nature of the various sensors required for
 digital avionics.
 As usual, I am interested in a least-cost approach ... I have more
 time than money.
 I suspect that many sensors would be available on the surplus market,
 if a guy knew what to look for.
 Does anyone have information on just what might work on these
 "experimental" systems and where they might be obtained?

 Robin Berglund

 DigiKey sells a lot of sensors.
 FreeScale makes low cost $10 pressure sensors the same ones Tracy
 uses. A lot of automotive sensors put out the industry standard
 0 to 5 volts. Thermal couples are needed for EGT so a thermal
 couple amplifier will be required to covert the millivolt TC
 signal to 0 to 5 volts needed by one or more of the 16 analog to
 digital processors in the ZBasic chip.

 Here is the function you use to get the digital
 value of an analog voltage appearing on Port F pins 29-36.

 GetADC       (subroutine form)
 Type         Subroutine
 Invocation   GetADC(pin, val)
 ..........   GetADC(pin, val, fullScale)
 ..........   GetADC(pin, val, fullScale, offset)

 Parameter Method Type ...  Description
 pin.....  ByVal  Byte ...  The pin from which to read an analog voltage.
 val.....  ByRef  Single..  The variable in which to return the result.
 fullScale ByVal  Single..  The full-scale voltage value.
 offset..  ByVal  Integral  The offset to apply before scaling.


 Discussion
 This function performs an analog-to-digital conversion on
 the signal present on the specified pin that must be one of
 the analog port pins.  The return
 value will be a 10-bit digital approximation of the input
 voltage with a range from zero to the AVcc reference
 voltage (usually +5 volts).  For the first form, the
 returned value is scaled to the range 0.0 to 1.0 and for
 the remaining forms it is scaled to the range 0.0 to value
 of the fullScale parameter.  For the third form, the value
 of the offset parameter (which could be negative) is added
 to the 10-bit ADC value before scaling.  This is useful,
 for example, for removing the effect of a non-zero offset
 voltage of the ADC.  You must make the pin an input before
 calling this routine.  The conversion is performed using
 the AVcc reference voltage.


 Resource Usage

 The ZX processors contain a single analog-to-digital
 converter thus allowing only one conversion to be performed
 at a time.  The conversion process takes approximately
 220uS during which time the calling task will be awaiting
 conversion completion.  Only analog port pins may be used
 to perform an analog-to-digital conversion.


 Paul Lamar


Paul,

Here is a project from Parallax, another uC for hobbyists that details
code and hardware for engine monitoring.  There is far more than you
need, but it is definately worth reading.

Fran

-- 
Sincerely, Fran Losey www.mykitlog.com\loseyf

The pdf is too large to publish Fran.
Looks like the system is from this company.
http://www.usmotion.com/daqpac.asp
http://www.parallax.com/tabid/477/Default.aspx
http://www.ubicom.com/products/mmprocessors.php


Perhaps it can be downloaded from some place.
Strangely a lot of the chips used are not identified.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.