I suggest if you are interested in this system you make
 a folder and drag over all the many future messages on this
 subject otherwise delete it.


 http://www.zbasic.net/

 So simple a caveman like me can do it.

 Paul Lamar

 ------------------------------------------------------

 I am just getting mine talking to my XP computer.

 If you plan to use the USB rather than the RS232 port for communicating
 you must do this.

 You will need to download USB drivers from the FTDI site and install
 them manually.  The FT232R drivers are available directly from FTDI at
 http://www.ftdichip.com/Drivers/VCP.htm.  Note that the CDM driver
 (whatever
 that is) is not  available for all operating systems.  Be sure to
download
 the drivers for the FT232R device that match your OS.

 snips...............

 Paul Lamar



 ------------------------------------------------------------------------------
 "The jumpers and switches are set at the factory assuming
 that the Dev Board will be powered via the on-board
 regulator and that a standard serial port will be used for
 communication with the ZX-1280N. If this is how you
 intend to operate it, simply connect an external supply to
 J27, connect your serial cable to J25 and activate the
 power switch. You should then see the output from the
 default ?Hello, world? program, confirming that the ZX-
 1280N is operating correctly and ready to accept your
 program."

 "If you intend to use the USB interface, several additional
 steps will be required. Firstly, change the switch SW3
 to the ?USB? position. If you also intend to power the Dev
 Board from your USB hub, move jumper J19 to the
 ?USB? position as well. Otherwise, connect an external
 power supply to J27. Connect a standard USB A-B
 cable between J28 of the Dev Board and your USB hub. When
 the power switch is activated, you should see
 several flashes on the Red/Green LED (D4, near the J28
 connector). "


 I got it working with the USB and an external power supply.
 There is a blinking LED near the USB connector on the board when
 it is communicating with the PC. This is what the screen
 in the Windows XP computer looks like.

 The next test will be the rotary engine compression tester
 program. If you have the board and you want to follow along
 and you run into a problem I'll try to help.

 ---------------------------------------------------

 The compression tester is working. It took 5 minutes
 to write the software and get it working.
 I had no pressure sensor connected to the A to D pin so it was
 reading max high or 254 and 255.

 One minor problem.

 I need to convert the extended ASCII output characters
 to a decimal number character so they can be loaded into
 a spread sheet for plotting.

 Anybody know how to do this in debug?
 A Windows problem.

 http://www.zbasic.net/

 So simple a caveman like me can do it.

 Paul Lamar

 SNIP!

 Paul, I saw some ascii to block text, crc, and a few other code
 samples on the Basic X example code section. But I'm not sure
 if any are exactly what you are looking for. Maybe you could give it a
 peek.
 C. Smith

 I think it has something to do with the debug.com program. I'll call Don
 Kinser later today and find out.

 Now I have some PC boards to build.


 Paul Lamar

 Paul,

 Can you walk me through this process.  I have the ZX board connected via
 USB.  (jumper J19 changed to USB; SW3 set to USB; FT232R s/w downloaded.
 Board appears to be working (green LED flashed a few times and the red
LED
 is on steady.  Got message that device has been configured.  However, I
 never saw the "Hello..." message.

 How do I proceed.  I've opened the ZBasic IDE program and it appears to
be
 running.  The compression-test1.bas is showing.  Where do I go from here?

 Thanks,
 Mark


Update...

I compiled the compression-test1.bas and got this error:

"C:\Program Files (x86)\ZBasic\zbasic.exe"  --target-device=ZX24
--directory="C:\Users\Mark\ZBasic/" "CompTest.bas"
CompTest.bas:2: Warning(3): parameter 1 of ADCtoCom1, pin 82 (&H52) is not
a
valid ADC pin for target processor "ZX24"
No errors.  Target device: ZX24, Code: 43 bytes, RAM: 0 bytes, Persistent
memory: 0 bytes
Exit code: 0

Any suggestions?

Mark S.

Go into the options menu scroll down to device options
and type ZX-1280n in the target device window.

click OK


Paul Lamar

--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.

Paul,

OK, I had initially downloaded the latest version, but went back and
downloaded the self executing driver.  Then, as you state above,I changed
device options to ZX-1280n, pressed "Reset",  I then tried to compile and
got this message,

"C:\Program Files (x86)\ZBasic\zbasic.exe"  --target-device=ZX1280n
--directory="C:\Users\Mark\ZBasic/" "compression-test1.bas"
Error: one or more errors occurred in the back-end build process for
"compression-test1.zxb"
Exit code: 1

Any suggestions?

Thanks,
Mark


Paul,

I tried typing in the sample program on pg 1 & 2 of the manual that flashes
the red and green LEDs.  I compiled it and got the same error message as I
got with your program, i.e. Error: one or more errors occurred in the
back-end build process for "FlashLED.zxb".  So, the problem may be something
more generic.  I'll try looking through the manual for some guidance.

Thanks,
Mark

Are you running XP? Do you want me to post the problem on the forum?

Paul Lamar