Subject: The Fires of Hell 10 degree multi-strike ignition system.
From: Rotary Engine
Date: 6/17/2010, 11:51 PM
To: AAA Put this in the To box

Scroll down to to the bottom Steve.
We do everything in chronological order.

Paul

This is a homebuilt MSD system with one  spark
every 10 degrees starting at 20 degrees BTDC.
400  watts ought to be plenty. No guarantee on
spark plug life however.  Try iridium.

I need to update 555 crank angle sensor 3 dwg to  show
more HE sensors.

Paul Lamar


Paul,

I like the design.  If I understand correctly, a  3-rotor would take three
of  the units shown in your drawing,  "High-Voltage half bridge
driver.jpg".
And there would be three  inverters required also?  Nice for redundancy,
but a
bit on  the heavy side.  What about the trailing plugs?

Mark

A three rotor would not need three units. Just one. The  stationary
disk is printed circuit board material with 3 groups of  hall efect
sensors equal spaced at 120 degrees.  Starting at 20  degrees BTDC
the HE's would then be at 10 BTDC, TDC, 10 ATDC and 20  ATDC.

Then for a 3 rotor the HE pattern would be repeated 120  degrees later.

snips...

Paul,

I understand the  groups of HE's spaced 120* apart, but I don't see how the
system knows  which coil to fire.  Please explain.

Mark

This schematic is  for a one rotor engine with one
coil and one spark plug.

Each plug  has its own coil. Each HE has its own capacitor discharge
system.  All  four HE/CD's  fire the one coil.  For every coil there
are four  HE/CD systems. Sounds complicated but the CD systems
and HE's are cheap.  The CD system mostly uses tiny little 8 pin
dips. What keeps the overall  cost down is the 220 volt power supply
common to six HE/CD  systems.

For your 3 rotor engine you would need six of these systems,  six coils
and one 220 volt power supply. Two per rotor. One for  leading
plugs and one for trailing plugs. Of course you could put a  reduced
capability, entirely different, less powerful system, on the  trailing
plugs.  Just to keep you flying.

If desired, for a bit  more redundancy, you could use two power supplies.
One for all the leading  plugs and another for all the trailing plugs.

You can also split the  timing by moving the trailing HE's on the printed
circuit  board.

Also re read: http://www.rotaryeng.net/Why-CDI.html

I  expect this system to put out a bit more power
with a lower BSFC. In other  words the same power
with a lower fuel burn.

Paul  Lamar


OK, so then you would need multiple units.  That makes  sense now.

Mark

It is the only way to be sure all the capacitors  are fully
charged at high RPM.

Paul Lamar


Hi guys,
I'm coming into this quite late, and don't have all of the background  info.

I don't know why it is thought that three Hall-effect sensors are required,
as if you have a flywheel with a ring gear, a pair of Hall-effect sensors
will  do.

One Hall sensor gives a signal to indicate absolute position of the rotors;
say for example 50° BTDC on rotor 1.
Another Hall sensor counts flywheel teeth, acting as a clock input to a
microcontroller that keeps track of how many degrees the engine has turned
since  the 50°BTDC input has occurred.

The engine RPM can also be determined by the flywheel tooth counter input -
or the absolute position input, whichever you prefer.

Steve in Orlando

Steve We are using a unusual micro controller that does not do counting
well. Check out AVR ZBasic 1280n. The up side is it is 10 times
easier to program. We trade off hardware for software.

Rotary engines are super simple so no counting of teeth is needed.
Just use another $1 HE as the rotors fire 180 out of phase once per RPM.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.