Subject: Dead time and thinking out loud. 2
From: Rotary Engine
Date: 6/25/2010, 10:42 AM
To: AAA Put this in the To box



   Dead time is the time between when the top FET switch is
   turned off and the lower FET switch is turned on.
   These are called totem circuits, push me pull me
   or huff and puff if it is a tandem engine airplane :)
   Normally this is controlled by and can be adjusted
   by the designer in the half bridge driver chips.
   It is like you have to turn off the front engine
   before you start the rear engine.

   I am using the AtMel ZBasic computer and opto couplers
   to simulate a half bridge driver chip. With the computer,
   the dead time can be anything controlled by the software
   but in this case I am using just a few micro seconds.

   Half bridge driver chips are normally used for
   switching power supplies that can oscillate at up
   to 100K Hertz (cps). Me and the Aussies are using
   them in a different way for capacitor discharge
   ignition systems. The top FET switch is on the vast
   majority of the time to charge the capacitor.

   When you need a spark, the top FET switch is turned
   off and the bottom FET is turned on for the length
   of time it takes the cap to discharge through
   the lower FET and the coil. Usually less than 100 micro
   seconds. Then it is turned off and the top FET turned on.

   Here is the software to do that.
   ===================================================
   Public x as long
   Public y as long

   Sub Main()
   for x = 1 to 100000000000 'keeps running until
   Debug.Print CStr(x)

   Call PutPin(12, ZXOutputHigh) 'top FET CD 1 on
   for y = 1 to 1000 '.......... .roughly 2.5 ms
   next y '...................... combined with debug.print
   Call PutPin(12, ZXOutputLow)   'top FET C1 1 off
   for y = 1 to 5 '............... dead time
   next y
   Call PutPin(13, ZXOutputHigh) 'lower FET CD 1 on
   for y = 1 to 50 '............. stays low for 100 uS
   next y
   Call PutPin(13, ZXOutputLow)   'lower FET CD 1 Off
   for y = 1 to 5 '............... dead time
   next y
   Next x

   End Sub
   ================================================

   The last thing you want to have happen is both
   FET switch's on at the same time. Our new 300 V power
   supplies have a safety feature so they would
   shut off if that happened for long. They also
   have a low voltage turn off so if the battery
   is less than 9 volts you get no ignition.
   The up side is your expensive ($150) power
   supply is not destroyed :)

   The cap is charging fine at around 16,000 RPM
   through a 2.5 ohm resistor simulating the coil.
   The Mazda 2nd gen trailing plug coil has
   less than 1 ohm DC resistance.

   The scope trace shows the voltage at the top
   of the cap. As you can see it is the power
   supply voltage for the majority of the time.
   It goes toward zero when the lower FET is
   turned on.

   BTW these are SMP60N05 FETs just because I happened
   to have a bunch. The lower the on resistance
   of the FET the better the ignition will work
   and the faster the cap will charge. I can't find
   any data on the SMP60N05 so I don't recommend it.
   Apparently it is obsolete.

   Paul

   Paul,

  Will it work at 21000 rpm?  That would be 7000 rpm on a 3-rotor.

  Do you really feed 300v into pin 4 of the optoisolator?

  Mark

  Good observation Mark.
  Not yet. I am not sure feeding 300 volts into an opto
  isolator will work but Pansonic claims to have some
  350 volt versions.  There are some on that DigiKey
  page you sent me down near the bottom. (attached)
  However the switching time is real slow at 40 us.
  That could be a show stopper for the opto version.
  Not for the half bridge driver version however.

  The current test rig is running on 8 volts.

  Regarding this on a 32 rotor:
  Maybe with better FETs but you would need a distributor
  if you are using only one CD system with one coil.

  You could make a distributor that worked off the nose
  of the e-shaft. Or get a pre 1989 Mazda distributer.
  As I recall those were two levels with two spark rotors so
  even those required two ignition systems with two coils.

  The real early models, back in the 70's, had two entirely
  separate distrubtors. Fortunately by the time
  the 3 rotor came out in the early 90's electronic ignition
  and CAS's came in to use.

  My vision is one of these for each leading plug
  and something else for the trailing plugs. So they only
  need to go to 7500 RPM.


  Paul Lamar

  Paul,

With a little finessing, you can fit three CAS pickups spaced 120* apart
into a 20B CAS housing.  That's how I'm triggering the three MSDs that I am
now running.  The CAS rotor turns at 1/2 engine speed, but there are two
pointers.  So, one of the pointers will align with one of the pickups every
120* of crank rotation.  Works for me.

Mark

Mark

Good work Mark. Cool.
So that was the original system you flew with before the RX8
trigger wheel? So Tracy redid his software or you don't use his
ignition wiring? I am glad you have some base line
fuel burn with that system.

Looks like it will work fine. At that diameter one must be careful
to get it at the exact angle. Did Bob set it up on his rotary
table?

I'll do some thing similar for the nose of the e-shaft
as soon as I get the multi-strike going except I will
need only one magnet and it will be larger in diameter
easing the angle problem.

Here is a picture of a stock 2nd gen CAS.
Got any pictures of your modification?

Is the high speed miss now gone?


BTW I think I found the ideal hot tip part. It has individual control
for both upper and lower FET. Just like the opto version but
no worries about high voltage opto's. It is called the L6388E.
If anything it is simpler to use than the L6383E I have now
and the IR2155 used in the Aussie system.

Here is the pdf and jpg for the L6388.

-------------------------------------------------

BTW Mark I was explaining your modified 2nd gen CAS to Robin
and the difficulty of getting the angle correct.
She suggested using the Hytek to record the ignt
timing. At 2000 samples per second it should do
a real good job of checking the timing.

Send me a schematic of how you are triggering
the MSD units and I will see if I can figure out
how to wire the opto's.

Pau Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.