Subject: Oil film strength tests
From: Rotary Engine
Date: 7/10/2010, 11:10 PM
To: AAA Put this in the To box


G'Day Paul,
I would again like to subscribe to your Newsletter.

A few years ago I was a subscriber. At that time I posed a
question regarding oil film strength in relation to the
normal Australian practice of using two stroke oil in the
sump of rotary engines, including those used in competition
as I was proposing to use it and circulate it  through one of
Tracey Crook's reduction drives. I was unable to find any
objective information to compare ATF and two stroke oil.

We built a fairly simple oil film strength testing device
giving us a reading on the load applied and the amount of
friction generated reading as amps. On being shown our results
recently Tracey remarked that the components of Mobil 1 were
responsible for a lot of apex seal problems. No such problems
appear to occur on two stroke oil here in Australia.

If you think your subscribers would find our results of
interest I would be happy to share them with you.

Let me know.

Regards

John Evans

Quote.
                        "On being shown our results recently Tracey remarked that the
components of Mobil 1 were responsible for a lot of apex seal
problems."

Whose apex seals? Tracy's apex seals? Stock Mazda apex seals?
Tracy is selling apex seals.

We have been running Mobil 1 for at least 25 years in our rotaries
with stock Mazda apex seals with no problems. We did a 500 F oil
bake test and Mobil 1 came out on top of all the oils we tested
except for turbine oil.

As far as I know, and some of the evidence would support that,
Tracy's apex seals are made from steel. We warned our readers 12 years
ago about making apex seals out of steel. Mazda apex seal history
also indicates that. Apparently and a lot of other info supports this,
cast iron is the best metal to make apex seals and piston rings
for that matter. Apparently it is porous on a microscopic level
and retains lubricant while steel does not. Mazda spent millions
coming up with this conclusion. The 13B apex seal environment is
severe with the seals running at over 500 F.

Does your film strength tester test at 500F?
Unless you are testing at 500 F you are not testing :)

What works best is Ianetti ceramic seals made from silicon nitride.
Silicon nitride is used in high speed ball bearings as it will
run over 1000 F while regular ball bearings start to have
problems at 500 F.

Read this http://www.rotaryeng.net/seals.html


Paul Lamar
 
Thanks for your reply Paul, I don't know anything about
Tracey's seals, I showed him the results in relation
to his gearbox. We certainly didn't attempt to "bake " the
oil in our tests, so far as I know what we did was a valid
test for oil film strength in a gearbox. Both the air cooled
and water cooled two stroke oils we tested were very good.

Perhaps one of your subscribers would be interested in
replicating our tests to  confirm/debunk our findings?

John Evans

I don't think running the engine oil in the gear box is
a good idea to begin with. You should use gear lube I suspect.
What do the Rotax guys do? Lots of two stroke Rotax's out
there with gear boxes.

Paul Lamar
                 _
John, I would like to see the some reference to the testing
protocol you are describing, for replication.
I work at the R&E Center for Ford Motor Company in
Dearborn MI. Having participated in numerous laboratory
and production automotive environments, it is clear that
he gathereing of data, and it's interpritation must be
clearly laid out, and of course repeatable.
I'm interested in replicating your testing protcol.
C. Smith

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.