Subject: Bought your book, but need some advice if possible
From: Rotary Engine
Date: 7/14/2010, 11:04 AM
To: AAA Put this in the To box


 Hello, Paul,

 I've read and re-read your book, "How To Cool Your Wankel" and find
 it fascinating. I, and my partners are building a Glasair Sportsman
 2+2 and installing an Eggenfellner 3.6L Subaru.  Next week we will
 have some expert help in fitting the custom Sportsman cowl we bought
 from Jan Eggenfellner. We expected this to be a relatively smooth job
 until I visited a good friend three weeks ago. This friend has been
 flying his Sportsman with the same 3.6L Egg Subaru for over a year,
 although he has only 60 hours on it. I asked him how he liked the
 engine, and his one big disappointment was the cooling. He told us
 that at 80F and higher, on any but the first takeoff of the day, he
 has to lower the nose to gain more airspeed, and loose a significant
 amount of climb performance, in order to keep the NPG+ (7psi cap)
 from overheating. Interestingly, he doesn't have a problem with
 overheating of his PSRU or the engine oil.

 This was devastating to us. We thought Jan had figured out the
 cooling problems on this engine, the most recent of his designs.

 If I may,I'd like to give you some facts and dimensions of the
 radiators and cowl system we purchased. We want to change what ever
 we reasonably can to get our Sportsman to be functional in over 80F
 weather.  We understand that very likely won't be optimized for drag.

 I'm attaching several photos which may help you visualize our
 situation.

 1. We have built (see photos) mockups of significantly larger
 radiators we'd like to have built hoping we can thereby increase the
 cooling. The original "radiators" Jan used are actually Niagara oil
 coolers. We've been told that a "true" radiator more efficiently
 cools water than an oil cooler does.

 2. We realize the larger radiators, which are wider and extend
 farther downward, are going to present challenges to duct the intake
 air over the entire face of the core.

 3. Changing to a somewhat thinner core should enhance air flow
 through core at climb speeds, so we are changing from 3 5/8 to 3 1/4
 thick core.

 4. If I read your book correctly, you indicate that will very short
 fore and aft distances, the trumpet shaped intake air duct is not
 advised unless we opened the inlet up and used a thicker core.

 Do you think that changes such as this would have a hope of giving us
 better cooling?

 It appears that a more radical approach, ditching the original Egg
 rads and engineering a belly-mounted radiator as you indicate on
 pages 35 - 40 would cool better. I'm sure I and my partners would
 prefer not to proceed on that route if the mods I've described would
 work.

 Finally, it appears on page 69 you warn against using a coolant such
 as Evans NPG+ because of its significantly lower heat transfer
 properties compared to water/anti-freeze mixtures. As I mentioned
 above, our friend flying the overheating Sportsman, is using NPG+. It
 appears to me we could increase our radiator effectiveness by
 switching to water/anti-freeze, but by how much I don't know.

 Thanks for any suggestions you care to offer.

 Dee Whittington

 Soobs should not be that hard to cool. A lot depends on
 one's gear box ratio. If it is say 2:1 and the engine
 is rated at 200 HP at 6500 RPM you will not get 200
 HP. If one's prop is about 70 inches in diameter
 it is limited to about 2700 RPM which is far cry from
 3250 prop RPM where max HP will occur. My guess on the
 real HP is closer to 170. Heat rejected is directly
 proportional to HP at the prop.

 3.6 L times 61 is 219 cubes so it is not a really big
 aircraft piston engine.

 In addition I think they reject less heat to the cooling
 system than a rotary. It also helps if you live in a northern
 climate as a one percent F increase in ambient is a one
 percent reduction in cooling for a liquid cooled airplane.

 What you have does not look all that bad. I would fly what
 you have first before ripping it all out and starting over.
 Airplanes take a long  time to build as it is.

 So far Evans coolant has not hurt the rotary but the cylinder
 head temperature  of a piston engine is higher by about
 100 F so you are taking a chance with Evans. The bottom line is
 the metal temp between the intake valve and exhaust valve
 within a mm of the combustion chamber. If it gets much above
 500 F bad things start to happen. The critical place in the
 rotary is just below the leading spark plug.

 BTW we have a summer special on the book for $30 cash.


 Paul Lamar

We have a local RV-8 with this engine, had a devil of a time getting
it to cool after the spring months.

The right side radiator is right up against the block.  If there is
any way to space it away so that air can penetrate the radiator, that
would help.

He also switched to a 16 lb. cap, eventually, and increased the exit
air at the bottom of the cowl, and added a radius, and made ducts to
mate up with the rads.

Also, I think the radiators are all plumbed in series (at least in his
aircraft they were), and then in parallel with the heater core.  Since
the heater core represented the path of least resistance, most of the
hot coolant was going through the heater core and very little of it
was getting to the radiators.  Most of the first flights were made by
only by the grace of thermal inertia, and those were once around the
patch type flights.

Chris Cosman




-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.