Hi Paul
I finish to renovate my new house and ready to go back on my project.
I will stay with p port intake and install turbo but i want to built my
own
drive with ford diezel trans 5R110W planet gear system.
the gear system is bigger then the E40D WITH RATIO OF 2.48.-6 pinion
planet
system Drum size 5"+
I look on the Slauson catalogue but i found a better price on EBAY
I intend to cruise at 6200 rpm approx and i would like to know the HP at
this
rpm for rx-8 pport and turbo.
i will also appreciate your comments
Jean Prudhomme
I think that gear set is overkill and too heavy.
Several people have used the A4OD set with three rotors.
One with a turbo 3 rotor. The ratio is not as good
as it is only 2.48 rather than 2.85.
Send me a dwg of the rest of the gear box.
The HP you get will depend on the boost. The fuel
burn will determine that at cruise. Figure a half pound
of fuel burned for every HP you choose. Fuel weighs
about 6.25 pounds per gallon.
P-port 2 rotors have been easily boosted to 400 HP
or more. Obviously you don't want to burn that much
fuel at cruise.
Paul Lamar
--
I just order parts from Slauson on E40D, it should be here next week.Will
folow with gearbox dwgs
Jean Prudhomme
Jean Prudhomme, I just thought I would share an idea on a part for your
CS Psru. The attached pictures are various four wheel drive front hubs. This
is a bolt on hollow spindle with a flanged wheel hub, The hub has internal
splines for the drive. The output from the planetary would be splined on
both ends. Early models from the 1970's are longer with widely spaced
bearings, Later models like the Dodge Dakota are more compact. This hub
would bolt on to the front of the gearbox providing a larger diameter
attachment to counter bending loads and gyroscopic loads. The spindles are
pilot bore mounted and have three to five attachment bolts. The Dakota shown
is an after market part with a full circular flange so you could have seven
attachment bolts. You would be looking for a 1/2 ton truck with a six bolt
wheel. The 8 bolt wheel parts are heavier and would also require an
additional adapter plate.
For my 4 rotor I have approximately 775 pounds of continuous thrust
load which should not be a problem bearing wise, and on the truck this part
sees 1500 pounds of static radial load. This should be workable with a 60
pound constant speed prop.
The new part price for the complete hub is around $90 on Ebay.
george grimes
What does that stuff weigh George? Would it not be better to spread
the bearings and use light weight needles? One would have to machine
these things to match the SAE prop flange. Do you have a dwg on the
truck front wheel bolt pattern? These things are designed for high
radial (vertical) loads and not optimized for gyro bending loads.
The low technical risk approach is to just copy the front
of a Lycoming crankcase and crank shaft. This has the advantage
of getting the high pressure oil pitch control oil into the prop
the same way Lycoming does it. One might be able to buy a cracked
Lycoming shaft and cut off most of it. The shaft seals are critical.
One pays a huge weight penalty using a 50 pounds metal constant speed
prop anyway as it adds to the shaft strength and bearing requirements.
The total weight is probably about 60 to 70 pounds. Governors also
cost close to $1000. On the other hand a fixed pitch composite
prop might be 20 pounds.
That opens up another approach to think about and that is the
fact that experimental's have a better power to weight ratio than a lot
of certified aircraft so there is less need for a low pitch prop on take off.
Just choose a good fixed pitch composite cruise prop and let the take off
performance be what it is. Runways are generally much longer than what
experimental's need.
--------------------------------------------------------------
Here is another way of attaching a flange to a light weight hollow
tubing shaft using needle bearings. Old Lou Ross largely got it
right except for the torque mitigator. Now that Jeff has an NC
lathe this becomes viable if he wanted to make psru's. Nothing
is selling right at the moment so it might have to wait till
the economy recovers if ever.
It will take a complete about face in Washington :)
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.